Cisco NCS 2000 series Скачать руководство пользователя страница 534

Страница: 534 / 602

Description

Error/Warning Message

Error/Warning
ID

The name must have a minimum of
six characters.

The name is too short. It does not have enough
characters. {0}

EID-2093

You must make sure the two fields
have the same password.

The password and confirmed password fields do not
match.

EID-2094

The password you entered is not
allowed.

The password is invalid. {0}

EID-2095

You must have an assigned security
level to perform this task.

The user must have a security level.

EID-2096

You did not specify a user name.

No user name was specified.

EID-2097

There was an error during the ring
switch.

An error occurred while ring switching.

EID-2099

You have not selected the profile to
delete.

Please select at least one profile to delete.

EID-2100

There was an error during the
protection switching.

An error occurred while protection switching.

EID-2101

The forced switch could not be
removed for some circuits. You must
switch these circuits manually.

The forced switch could not be removed for some
circuits. You must switch these circuits manually.

EID-2102

There was an error during the span
upgrade.

An error occurred while upgrading the span.

EID-2103

This error occurs during the path
protection span upgrade procedure.

The circuits cannot be switched back because one or
both nodes are not reachable.

EID-2104

You must supply a name for the node.

The node name cannot be empty.

EID-2106

There was an error adding the
specified item.

An error occurred while adding {0}. The host is
unknown.

EID-2107

The specified item exists in the
network.

{0} is already in the network.

EID-2108

The node you are trying to add is
already present in the current login
group.

The node is already in the current login group.

EID-2109

You must enter a number in the range
between 0 and the specified value.

Please enter a number between 0 and {0}.

EID-2110

Select a node ID that is not in use.

This node ID is already in use. Please choose another.

EID-2111

CTC cannot set the BLSR/MS-SPRing
extension byte.

The extension byte for the ring cannot be set. {0}

EID-2113

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

488

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды