Cisco NCS 2000 series Скачать руководство пользователя страница 586 | Manualshive

Страница: 586 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

One of the following conditions is
present: duplicate shelf positions,
invalid shelf positions, or concurrent
movement (two CTC sessions are
attempting to rearrange the shelves at
the same time.)

The shelves could not be rearranged. {0}

EID-6119

Refer to the error message text.

This equipment does not support multishelf.

EID-6120

The end points of an internal
patchcord should have compatible
wavelengths.

This internal patchcord cannot be provisioned because
the endpoints have no compatible wavelengths.

WID-6121

CTC was unable to initiate the wizard
due to the specified reason.

The wizard could not be started. {0}

EID-6122

A communication failure occurred.

The OSI request can not be completed successfully.

EID-6123

Refer to the error message text.

The ALS recovery pulse interval is invalid.

EID-6124

Refer to the error message text.

The ALS recovery pulse duration is invalid.

EID-6125

Refer to the error message text.

The current setting does not support the specified ALS
mode.

EID-6126

Refer to the error message text.

All enabled routers are required to have the same area.

EID-6127

Refer to the error message text.

A software download is in progress. Configuration
changes that result in a card reboot cannot take place
during a software download. Please try again after the
software download is done.

EID-6128

Refer to the error message text.

The payload configuration and card mode are
incompatible.

EID-6129

A data communication channel (DCC)
already exists.

A DCC is present.

EID-6135

CTC was not able to provision the
specified port or card.

An error occurred during provisioning: {0}

EID-6136

Multishelf is not supported on
equipment, is already disabled, or
modules on the shelf are currently in
use.

Multishelf cannot be disabled. {0}

EID-6137

Verify the LAN configuration.

The LAN configuration is invalid.

EID-6138

Non-DWDM cards cannot be added
to an a DWDM node. Remove the
cards.

Invalid card(s) are present. Please remove all
non-MSTP cards and try again.

EID-6139

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

540

Error Messages

Error Messages Reference

«
...
584
585
586
587
588
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: D-Linke Страницы: 32

Бренд: NEC Страницы: 47

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

ARM Cortex-A9 MPCore

Бренд: Dave Embedded Systems Страницы: 67

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: Profile Страницы: 6

Бренд: Maxim Страницы: 14

Бренд: LevelOne Страницы: 31

Бренд: Patton electronics Страницы: 12

Бренд: WAGO Страницы: 48

Бренд: ADTRAN Страницы: 4

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: ZyXEL Communications Страницы: 23

Бренд: Renesas Страницы: 67

Бренд: ZALMAN Страницы: 32

TEG-S16R - DATA SHEETS

Бренд: TRENDnet Страницы: 12

Бренд: Patton electronics Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды