Cisco NCS 2000 series Скачать руководство пользователя страница 579 | Manualshive

Страница: 579 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Select the correct payload.

The time slot selected does not match the payload.

EID-5220

Select the correct payload.

The ODU-1 selected does not match the payload.

EID-5221

Refer to the error message text.

Deleting the following OCH TRAIL circuit(s) will
cause the Layer2 services (SVLAN, EVC and MPLS
TP Tunnel) provisioned on them to go PARTIAL.

WID-5221

Refer to the error message text.

This platform does not support power monitoring
thresholds.

EID-6000

Check whether all the cross-connect
cards are installed and working.

One of the XC cards has failures or is missing.

EID-6001

Unlock the cross-connect card.

One of the XC cards is locked.

EID-6002

Enter a new ID for the ring.

The OSC termination could not be created. This ring
ID is already assigned.

EID-6003

Remove the BLSR from the node and
continue with the reset procedure.

A system reset cannot be performed while a BLSR ring
is provisioned on the node.

EID-6004

Refer to the error message text.

The timing references could not be assigned. - Only
two DS1 or BITS interfaces can be specified. - DS1
interfaces cannot be retimed and used as a reference. -
BITS-2 is not supported on this platform.

EID-6005

Refer to the error message text.

The timing references could not be assigned. - An NE
reference can only be used if the timing mode is LINE.
- A BITS reference can only be used if the timing mode
is not LINE. - A Line reference can only be used if the
timing mode is not EXTERNAL.

EID-6006

Refer to the error message text.

SF BER and SD BER are not provisionable on the
protect line of a protection group.

EID-6008

Refer to the warning message text.

If autoadjust GFP buffers is disabled, GFP buffers
available must be set to an appropriate value based on
the distance between the circuit endpoints.

WID-6009

Refer to the warning message text.

If auto detection of credits is disabled, credits available
must be set to a value less than or equal to the number
of receive credits on the connected FC endpoint.

WID-6010

Refer to the warning message text.

Ingress idle filtering should be turned off only when
required to operate with non-Cisco Fibre
Channel/FICON-over-SONET equipment.

WID-6011

You cannot change the timing
configuration on this port unless the
circuits on this port are deleted.

The retiming configuration could not be changed
because there are circuits on this port.

EID-6012

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

533

Error Messages

Error Messages Reference

«
...
577
578
579
580
581
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: A-Link Страницы: 6

Бренд: Rain Bird Страницы: 17

Бренд: Pakedge Device & Software Страницы: 20

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

Бренд: TC Electronic Страницы: 55

Z3-DM8168-PCI-RPS

Бренд: Z3 Technology Страницы: 20

Z3-DM8107-SDI2-RPS

Бренд: Z3 Technology Страницы: 75

Бренд: Z-Wave Страницы: 13

Бренд: Amperes Страницы: 8

Бренд: NetBurner Страницы: 15

Бренд: TRENDnet Страницы: 2

Бренд: Sangamo Страницы: 2

Бренд: Cypress Semiconductor Страницы: 10

Barricade SMC7901WBRA2

Бренд: SMC Networks Страницы: 2

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: TP-Link Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды