Cisco NCS 2000 series Скачать руководство пользователя страница 543 | Manualshive

Страница: 543 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

There was an error while retrieving
the defaults from the specified node.

An error occurred while retrieving defaults from the
node: {0}

EID-3002

CTC cannot load the specified file.

The file {0} cannot be loaded.

EID-3003

Refer to the error message text.

Properties cannot be loaded from the node.

EID-3004

CTC cannot save the network element
(NE) update values to the specified
file.

NE update properties cannot be saved to the file {0}.

EID-3005

Refer to the error message text.

NE update properties cannot be loaded from the node.

EID-3006

There was a provisioning error for the
specified item.

An error occurred while provisioning the {0}.

EID-3007

You cannot perform DWDM
automatic node setup (ANS) from the
Card view. Please navigate to the
Node view and try again.

This is not a valid card.

EID-3008

Select the specified item, for example,
VLAN, port, slot, etc.

No {0} was selected.

EID-3009

Refer to the error message text.

A bidirectional optical link could not be created.

EID-3010

Refer to the error message text.

The subnet address is invalid.

EID-3016

Refer to the error message text.

The subnet address already exists.

EID-3017

Enter the complete internal subnet
address.

The internal subnet address is incomplete.

EID-3019

A node internal subnet must be
different from one another as each
TSC is on separate ethernet buses,
isolated by broadcast domains.

The subnet address cannot be the same for both TSC
cards. The requested action is not allowed.

EID-3020

Refer to the error message text.

An error occurred while retrieving the diagnostics: {0}

EID-3021

The requested action is not allowed.

The requested action is not allowed.

EID-3022

Refer to the error message text.

The low order cross-connect mode could not be
retrieved.

EID-3023

CTC cannot switch the cross-connect
mode for the specified item, as the
type or the number of circuits does not
match with the criterion for switching
modes.

The {0} cross-connect mode could not be switched.
Please verify that the type and/or number of circuits
provisioned does not exceed the criterion for switching
modes.

EID-3024

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

497

Error Messages

Error Messages Reference

«
...
541
542
543
544
545
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: Ebyte Страницы: 8

Бренд: JCG Страницы: 2

Бренд: QNAP Страницы: 20

Бренд: Dahua Страницы: 24

Бренд: Netopia Страницы: 38

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

Бренд: Maipu Страницы: 80

18x18 Card Cage

Бренд: WolfPack Страницы: 31

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: C&T Solution Страницы: 129

Бренд: HighPoint Страницы: 10

Бренд: ZyXEL Communications Страницы: 170

Бренд: ZoneVu Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды