manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

This line cannot be put into loopback while it is in use
as a timing source.

EID-6088

CTC cannot find the specified
interface.

The interface was not found. {0}

EID-6089

Choose another interface.

The interface type is not valid for this operation. {0}

EID-6090

The port is in an invalid state to set a
loopback.

The current state of the interface prohibits this
operation. {0}

EID-6091

CTC does not allow this operation for
the specified interface.

This operation is prohibited for this interface. {0}

EID-6092

You have exceeded the number of
characters permitted.

The maximum number of TARP data cache entries has
been exceeded.

EID-6093

Refer to the error message text.

The maximum number of manual adjacency table
entries has been exceeded.

EID-6094

Refer to the error message text.

The AIS/Squelch mode is invalid.

EID-6095

Refer to the error message text.

A default IP-over-CLNS tunnel route is only allowed
on a node without a default static route and a default
router of 0.0.0.0.

EID-6096

Specify another authorization key.

The authorization key does not comply with Cisco IOS
password restrictions. {0}

EID-6097

Refer to the error message text.

A default static route is not allowed when a default
IP-over-CLNS tunnel exists.

EID-6098

Create the subnet on an active router.

You cannot create a subnet on a disabled router.

EID-6099

Refer to the warning message text.

Disabling a router that has a provisioned subnet is not
recommended.

WID-6100

Refer to the error message text.

The MAT entry already exists.

EID-6101

Refer to the warning message text.

The new card has less bandwidth than the current card.
Circuits of size VT15 and larger will be deleted.

WID-6102

Specify another entry for TARP Data
Cache.

The TDC entry already exists.

EID-6103

Automatic Power Control is aborted.

APC ABORTED.

EID-6104

Refer to the error message text.

The 'Change Card' command is valid for MRC cards
only when Port 1 is the sole provisioned port.

EID-6105

Disable Radius authentication and
proceed.

To delete all RADIUS server entries, RADIUS
authentication must be disabled.

EID-6106

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

538

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Abus TVVR36500 User Manual preview
TVVR36500
Бренд: Abus Страницы: 60
Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Бренд: Patton electronics Страницы: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Бренд: Paradyne Страницы: 12
TC Electronic ATAC Service Manual preview
ATAC
Бренд: TC Electronic Страницы: 55
Vonets MINI300 Quick Setting Manual preview
MINI300
Бренд: Vonets Страницы: 8
Intel Optane M Series Installation And User Manual preview
Optane M Series
Бренд: Intel Страницы: 59
DAD DPX2060 User Manual preview
DPX2060
Бренд: DAD Страницы: 32
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Бренд: Quectel Страницы: 23
Bridgeworks a204 Hardware Manual preview
a204
Бренд: Bridgeworks Страницы: 18
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Бренд: e-con Systems Страницы: 9
Idis DR-8400 Installation Manual preview
DR-8400
Бренд: Idis Страницы: 31
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Бренд: Acces I/O products Страницы: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Бренд: Enertronica Santerno Страницы: 34
Brocade Communications Systems NetIron MLXe Series Hardware Installation Manual preview
NetIron MLXe Series
Бренд: Brocade Communications Systems Страницы: 305
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Бренд: Danville Signal Processing Страницы: 35
VoiceLine InnoMedia MTA 3328-2R Getting Started Manual preview
InnoMedia MTA 3328-2R
Бренд: VoiceLine Страницы: 18
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Бренд: Lattice Semiconductor Страницы: 12
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Бренд: Isee Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды