Cisco NCS 2000 series Скачать руководство пользователя страница 532 | Manualshive

Страница: 532 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

An internal error occurred in Network
Alarm tab while synchronizing alarms
with the nodes.

A communication error occurred: {0}

EID-2056

There was an error during the node
deletion.

An error occurred while deleting the node. {0}

EID-2059

CTC could not find any protection
channel access (PCA) circuits for this
task.

No PCA circuits were found.

EID-2060

There was an error defining the
VLAN.

An error occurred while provisioning the VLAN.

EID-2061

Refer to the error message text.

An error occurred while deleting VLANs. No VLAN(s)
were selected. Please select a VLAN.

EID-2062

The selected VLAN is the default
VLAN and cannot be deleted.

The default VLAN cannot be deleted.

EID-2063

There was an error deleting the
specified VLAN.

An error occurred while deleting VLANs. {0}

EID-2064

Cannot import the profile because the
profile has reached the maximum
number of copies in the editor.

The profile cannot be imported. The profile "{0}" exists
in the editor and the maximum number of copies (ten)
exists in the editor. The import will be aborted. The
profile has already been loaded eleven times.

EID-2065

CTC encountered an error while trying
to store the profile.

The profile could not be stored. An error occurred while
writing to {0}.

EID-2066

CTC encountered an error while
writing the specified file.

An error occurred while writing to the file. {0}

EID-2067

CTC encountered an error trying to
load the alarm profile from the node.

The alarm profile could not be loaded from the node.

EID-2068

Either the specified file was not found,
or there was an input/output exception.

The file could not be found or an I/O exception
occurred. {0}

EID-2069

There was a failure in deleting the
specified profile.

The profile could not be deleted. {0}

EID-2070

You cannot select more than one
column during clone action.

Only one column may be highlighted.

EID-2071

You cannot select more than one
profile.

Only one profile may be highlighted.

EID-2072

You cannot delete a permanent
column.

This column is permanent and cannot be removed.

EID-2073

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

486

Error Messages

Error Messages Reference

«
...
530
531
532
533
534
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: GE Страницы: 4

Бренд: Paradyne Страницы: 22

Бренд: Panasonic Страницы: 4

Бренд: Patton electronics Страницы: 8

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Salus Страницы: 16

Бренд: Danfoss Страницы: 61

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

Бренд: Commell Страницы: 36

LinkSmart KW6515

Бренд: Kasda Страницы: 31

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

Бренд: Justec Страницы: 61

Бренд: Patton electronics Страницы: 12

Бренд: TP-Link Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды