Cisco NCS 2000 series Скачать руководство пользователя страница 531 | Manualshive

Страница: 531 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

CTC cannot find an attribute for the
specified item.

The attribute for {0} cannot be found.

EID-2037

The protection operation you tried to
execute is invalid.

The protection operation is invalid.

EID-2038

You must select a node before
performing the task.

Please select a node first.

EID-2040

You must select a link that has paths
available.

No paths are available on this link. Please make another
selection.

EID-2041

Refer to the error message text.

This span is not selectable. Only the green spans with
an arrow may be selected.

EID-2042

Refer to the error message text.

This node is not selectable. Only the source node and
nodes attached to included spans (blue) are selectable.
Selecting a selectable node will enable its available
outgoing spans.

EID-2043

You must select only one link going
in and out of a node. Selecting more
than one link is contradictory to the
path selection algorithm.

This link may not be included in the required list.
Constraints only apply to the primary path. Each node
may have a maximum of one incoming signal and one
outgoing link.

EID-2044

Refer to the error message text.

This link may not be included in the required list. Only
one outgoing link may be included for each node.

EID-2045

There was an error due to an invalid
slot number.

Please enter a valid value for the slot number.

EID-2047

There was an error due to an invalid
port number.

Please enter a valid value for the port number.

EID-2048

CTC could not destroy the new circuit.

The new circuit could not be destroyed.

EID-2050

The specified circuit cannot be
downgraded.

The circuit cannot be downgraded. {0}

EID-2051

There was an error during the circuit
processing.

An error occurred during circuit processing.

EID-2052

There was an error during the endpoint
selection.

An error occurred while selecting an endpoint.

EID-2054

This error occurs in the circuit creation
dialog only during a race condition
that has incorrectly allowed entities
without endpoints to be displayed in
the combination boxes.

No endpoints are available for this selection. Please
make another selection.

EID-2055

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

485

Error Messages

Error Messages Reference

«
...
529
530
531
532
533
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: D-Link Страницы: 13

Бренд: A10 Страницы: 52

Бренд: Maxim Страницы: 26

Бренд: NetComm Страницы: 3

Бренд: Klark Teknik Страницы: 50

Бренд: Alesis Страницы: 61

Бренд: FS Страницы: 19

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Бренд: ZyXEL Communications Страницы: 282

Бренд: EVOC Страницы: 57

PISO-725 Series

Бренд: ICP DAS USA Страницы: 8

Бренд: addlink Страницы: 9

1394 Dual-Port CardBus

Бренд: SIIG Страницы: 8

Бренд: ZALMAN Страницы: 11

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Vocal Performer VE-20

Бренд: Boss Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды