background image

 

323349A-01

October 2002

©

 2002 National Instruments Corp. All rights reserved.

FieldPoint™, National Instruments™, NI™, and ni.com™ are trademarks of National Instruments Corporation. 
Product and company names mentioned herein are trademarks or trade names of their respective companies. 
For patents covering National Instruments products, refer to the appropriate location: 

Help»Patents

 in your software, 

the 

patents.txt

 file on your CD, or 

ni.com/patents

.

FieldPoint Operating Instructions

FP-RTD-124 

AND C

FP-RTD-124

Eight-Channel Four-Wire RTD 
and Resistance Input Modules

These operating instructions describe how to install and use the 
National Instruments FP-RTD-124 and cFP-RTD-124 three-wire 
RTD and resistance input modules (referred to inclusively as the 
[c]FP-RTD-124). For details on configuring and accessing the 
[c]FP-RTD-124 over a network, refer to the user manual for the 
FieldPoint network module you are using.

Features

The [c]FP-RTD-124 is a FieldPoint RTD and resistance input 
module with the following features:

Inputs for 100

 platinum RTDs (resistance temperature 

detectors)

Built-in linearization for six TCR (temperature coefficient of 
resistance, or alpha) values of RTDs

Direct resistance measurements with a 400

 range

Four-wire measurement for high accuracy

16-bit resolution

Filtering against 50 and 60 Hz noise

2,300 V

rms

 transient overvoltage protection

–40 to 70 °C operation

Hot plug-and-play

Содержание Fieldpoint cFP-RTD-124
















Отзывы: