manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 69

Issue 1.0

March 2001

2-15

365-575-389

Installation Manual

System Installation Planning

Optical Translator Basics

Description

Optical Translator Units are used with Optical Line Systems to perform the 
following functions:

■

Connecting OC-48/STM-16, OC-12/STM-4, OC-3/STM-1, 100 to 750 Mb/s 
or 1-Gb Ethernet systems with non-OLS-compatible optics to an OLS

■

Signal Regeneration between concatenated OLS

■

Wavelength Translation between concatenated OLS

■

Wavelength Add/Drop between OLS

Connecting Non-
OLS-Compatible 
Optics to WaveStar 
OLS 40G

Optical Translator Units receive any standard optical wavelength with an OC-48, 
OC-12, OC-3, 100 to 750 Mb/s, or 1-Gb Ethernet signal and apply that signal to 
an OLS compatable optical wavelength while providing an OLS identification tone.  
Figure 2-13 shows Optical Translators being used with an OC-48 system.

Figure 2-13. OT Connecting Non-OLS-Compatible Optics to WaveStar OLS 

40G

In OLS 40G systems with many repeater amplifiers, drop OTUs or OLS-
compatible receivers are always required to guarantee performance. For shorter 
OLS 40G systems performing fiber congestion relief or metro/regional distribution, 
the existing customer standard receivers may perform sufficiently so the drop 
OTU is not needed.

The following requirements must be met to omit the drop OTU:

■

The receiving equipment must be co-located with the OLS 40G equipment. 
The fiber jumper loss between the ODU on the OLS and the receiver must 
have less than 0.5 dB loss. If the receiving equipment is not co-located with 
the OLS 40G, then a drop OTU is required.

(Continued on next page)

Non-OLS

Compatible

OC-48

OLS

End

Terminal

Optical

Translator

TRMTR

RCVR

OTU

OTU

OMU

ODU

Non-OLS

Compatible

OC-48

OLS

End

Terminal

Optical

Translator

RCVR

TRMTR

OTU

OTU

ODU

OMU

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды