manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 554

E-12

Issue 1.0

March 2001

365-575-389

Installation Manual

Harris C-1000 Centurion Installation —Extended 
Miscellaneous Discretes

Provisioning Extended Miscellaneous 
Discretes

Enabling SER 
TLM 1 Port

The SER TLM Port must first be enabled through the CMC by using the following 
command: SECURITY.ENTER.Channel Identifier.SECURITY. Enter: SER_TLM1 
in the AID and at Port ACC enter ACC.

Extended 
Miscellaneous 
Discrete 
Assignments

The Miscellaneous Discrete Assignments are provisioned by using the following 
command through the CMC:

CONFIGURATION-SET-ATTRIBUTE-ENVIRONMENT.

Enter the Alarm number (i.e., 28) in the blank AID box.

This input sets the Descriptions and Alarm Levels for the miscellaneous discrete 
inputs.

■

The Point parameter selects the miscellaneous discrete input point to 
provision

NOTE:

The miscellaneous discrete points 1-16 are assigned to the original 
miscellaneous discrete ports. Therefore the extended miscellaneous 
discretes will begin their assignment with point number 17 and continue 
through point number 144.

■

The Alarm Level Parameter provisions the severity of the condition 
associated with the closing of the selected miscellaneous discrete input 
point. The choices are:

— "CR": critical

— "MJ": major

— "MN": minor

— "NA": status not alarmed

— "NR": status not alarmed and not reported to the OS.

(Continued on next page)

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды