manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 195

Issue 1.0

March 2001

5-39

365-575-389

Installation Manual

Wired Cable Installation

OLS/OT Integration Cables 
Installation

Description

Release 3 OLS/OT Integration provides a control interface between the OLS and 
the OT. An OTCTL (LUD1) pack is inserted in the OT System Shelf, and cables 
are installed which connect the OT to the OLS. This integration provides additional 
maintenance information and control of OT provisioning and administration 
through existing OLS control interfaces.

!

WARNING:

The following installation procedures are for new installations. Using these 
procedures on "In Service" OLS/OT systems will result in a "Loss of 
Service." For "In Service" upgrades use the appropriate MIP.

Configurations

There are two integrated OLS/OT configurations:

■

One OLS shelf with one OT system,

■

One OLS shelf with two OT systems.

An OT system can consist of one, two, or three shelves.

One OLS Shelf/
One OT System

Table 5-23 lists the cables available for interconnecting one OLS shelf and one 
OT system.

Table 5-23. One OLS Shelf to One OT System Interconnection Cables

(Continued on next page)

ED-7C028-22

Cable Group

Cable Length

(ft.)

Connections

OLS

OT

801

20

P14

BUS OUT

J5

J6

IAO LAN

CTL IN

851

100

853

200

855

180

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды