manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 198

5-42

Issue 1.0

March 2001

365-575-389

Installation Manual

Wired Cable Installation

OLS/OT Integration Cables 
Installation (Continued)

One OLS Shelf/
One OT System 
(continued)

NOTE:

For an OLS to be initially equipped with a single OT and later to be 
expanded to a second OT, the OLS and OT should be installed with the 
Dual Reset and Equipage cable G812, G813, or G814. The total cable 
length between the OLS, OT Bay # 1, and the eventual OT Bay # 2 must be 
planned such that the length of LAN Cable 1 (G801, G851, G853, and 
G855) and the eventual LAN Cable 2 (G806, G807, G808, G809) will not 
exceed 200 ft. The appropriate Dual Reset and Equipage cable should be 
chosen based on the maximum distance between the OLS and either OT 
Bay # 1 or OT Bay # 2.

When installing the OLS and OT Bay # 1, the LAN path must be terminated at the 
last OT Bay # 1 shelf at backplane connector J7 using termination plug 
ED-7G045-20 G2. This termination plug must remain in place for single OT bay 
operation. 

The OT Bay # 1 to OT Bay # 2 LAN cable is to be routed and left unconnected. 
The unused branch of the Dual Reset and Equipage cable may be coiled and 
stored until needed with no special termination required on the other end. 

When OT Bay # 2 is installed, the OT Bay # 1 LAN termination plug is removed 
from J7 on the OT Bay # 1 backplane and the appropriate LAN Cable 2 group is 
installed. The previous unused branch of the dual reset and equipage cable is 
connected to OT Bay # 2, and the Group G803, G804, or G805 cable of proper 
length is installed between the OLS an OT Bay # 2.

One OLS Shelf/
Two OT Systems

Table 5-24 lists the cables available for interconnecting one OLS shelf and two OT 
systems. There are four types of cables, available in three or four different 
lengths. Only one of each type of cable is needed. 

The cable with group numbers 801, 851, 853, and 855 and the cable with group 
numbers 806, 807, 808, and 809 are both LAN cables. The combined length of 
these cables in the system can not exceed 200 feet.

(Continued on next page)

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды