Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 120

3-44

Issue 1.0

March 2001

365-575-389

Installation Manual

Equipment Installation

Miscellaneous Mount Installation
(Continued)

Vertical Space
Requirements

When installing shelves in the bay frame, the following mounting requirements
must followed:

■

The heat baffle mounted to the bottom of each shelf must be installed with
each shelf. The heat baffles are not to be removed from any shelf.

■

The mounting bracket hole separation of 11 inches, as shown in
Figure 3-14 on page 3-42, must be maintained for the miscellaneous OT
shelves. The supplied interconnecting cables will not be long enough for a
larger separation.

■

Either another heat baffle or an open space of three (3) inches is required
for cooling at the top of each OLS or OT miscellaneously mounted shelf
installation. The shelves may be mounted at any height ranging from the
lower heat baffle touching the base of the bay, to any distance above the
base, as long as the top clearance of 3 inches or greater is maintained.

The total height required for the various OT List structures is as follows:

Adjustment of
Side Mounting
Brackets

The side mounting brackets of the OLS and OT shelves are factory installed for
mounting to the narrow mounting flange of a Lucent Technologies 800 Type bay
frame. These brackets are identified by the letters L and R stamped on them.

For mounting to the Lucent Technologies 801 Type frame using the wide mounting
flange, the bracket needs to be moved forward to another set of mounting holes.

For other bay frame types, the bracket should be positioned to provide the best
overall results or removed entirely and the shelf mounted using the front flanges.

(Continued on next page)

List Number

Vertical Space Required

List 10

66 Inches

List 11

24 Inches

LIst 12 with List 11

45 Inches

List 13 with List 11 and 12

66 Inches

«
...
118
119
120
121
122
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды