Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 128

4-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Power Cable Installation

Background

Introduction

The procedures in this installation manual are only to be performed by trained
personnel.

This section covers WaveStar™ Optical Line System (OLS) 40G Power (battery A
and battery B) cable installation for cabinets, integrated bays, multi-shelf bays,
miscellaneous mount configurations.

General
Considerations

A wrist strap, connected to a wrist strap ground jack on the terminal must be worn
for ESD protection during the installation process.

Connectors on the interconnect panel come equipped with protective ESD covers.
These covers should be left in place on any connector that is not being
immediately cabled so that ESD protections are maintained.

!

WARNING:

Unterminated optical connectors may emit laser radiation and should not be
viewed with optical instruments (other than indirect image-converting
devices). Also avoid direct exposure to the beam.

Keep the following information under consideration during cable installation:

■

This cable information is the latest cable information available at the time of
the issue. For up-to-date information, refer to the ED cable drawings listed
in

Chapter 1, Overall Installation and Test Considerations

.

■

For ordering information, refer to 365-575-380, Optical Line System (OLS)
Application, Planning, and Ordering Guide (APOG) and the Optical
Translator (OT) Application, Planning, and Ordering Guide.

■

Do not remove the shelf backplane cover during the installation process.

«
...
126
127
128
129
130
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды