manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 438

10-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Fiber Connections

Overview

Basic Information

This section describes how to establish the optical line system. Some general 
information on lightwave jumpers and optical line buildouts is given in the following 
sections as a quick reference. Refer to 365-575-387 WaveStar OLS 40G User/
Service Manual for complete details. Read and understand the optical line 
buildout selection procedure before starting to connect fibers.

General 
Considerations

Note the following before starting the procedures which follow: 

n

Disconnect the office alarms cable at the WaveStar OLS 40G Network 
Element before performing any tests. Reconnect the office alarms cable 
after completing tests.

n

Be sure each Network Element has completely passed all of the tests in 
the previous sections of this document. 

n

Required equipment is listed in Section 1 of this document, “Overall 
Installation and Test Considerations”. An optical power meter is needed to 
perform the steps in this section.

n

A general familiarity with the CMC is assumed, each and every key stroke 
is not detailed. Refer to the 365-575-387 WaveStar OLS 40G User/Service 
Manual, Tab 11, “Craft Interface Terminal Usage”, or Appendix F of this 
document for complete CMC use instructions.

n

Do not use cable ties with the optical fiber.

n

Place optical fiber jumpers in protective tube or channel, such as polyvinyl 
chloride (PVC) tubing when running the cable from the WaveStar OLS 40G 
to the cable rack. Protective tubing is supplied in the Installation Kit 
(C848065959).

n

Place optical fiber jumpers in the cable rack in a protective channel with 
nothing on top of them. 

n

Maintain a minimum of 1.5 inches of optical fiber bend radius. 

n

Optical fiber jumpers require ST, FC, LC, or SC type connectors for 
connection to the WaveStar OLS 40G. 

n

Before removing a fiber jumper from an OA output connector, the safest 
way to avoid damage and minimize the power level is to first unseat the OA. 

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды