manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 530

C-12

Issue 1.0

March 2001

365-575-389

Installation Manual

Fiber Cleaning

Cleaning/Inspecting Optical 
Connectors (Continued)

Optical Fiber 
Adapters and 
Circuit Pack 
Connectors

During testing and/or trouble shooting activities it may be necessary to clean the 
optical buildout adapter and the circuit pack connector. 

NOTE:

Do not attempt to clean ports equipped with yellow lightguide buildout 
(LBO) attenuators. Attenuators contain a thin glass lens that is extremely 
fragile and would be damaged by cleaning by a mechanical means. Discard 
any contaminated LBOs.

The following procedure is recommended.

Step

Action

1 

Using the appropriate CLETOP stick cleaner (2.5 mm for SC, ST, and FC 
connectors, 1.25 mm for LC connectors) dampen the stick cleaner with 
Ethyl alcohol using the alcohol wipe. Insert the stick cleaner into the 
adapter rotating the stick 360 degrees while inserting. Push/rotate stick 
until the stick cleaner makes contact with the ferrule end face. Apply 
slight pressure upon contact and rotate stick 360 degrees at least three 
(3) times.

2 

Remove the stick cleaner rotating it upon removal.

3 

Using a dry CLETOP stick cleaner of appropriate diameter, repeat the 
above cleaning procedure. This procedure will clean the sidewalls of the 
adapter and the endface of the circuit pack connector.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды