Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 170

5-14

Issue 1.0

March 2001

365-575-389

Installation Manual

Wired Cable Installation

Serial, Parallel, and X.25 Telemetry
Cable Installation

OLS Serial
Telemetry Cables
Installation

Serial telemetry (TBOS) provides information to the maintenance center about
that location and remote control over that location from the maintenance center. In
Releases 2.0 and 2.1 OLS, the Ser Tlm 1 port will support the Extended
Miscellaneous Discretes feature. This involves connecting the Ser Tlm 1 port to
an Extended Miscellaneous Unit (EMDU) located outside of the OLS system.
Appendix D and Appendix E covers the installation of the EMDU to the OLS
system. In Release 3.0, the OT and OLS can be integrated as a single network
element and the EMDU is no longer necessary to monitor the OT CP Fail and
LOS alarms. However, the EMDU may still be used to monitor other
Miscellaneous Discrete alarm points to provide an additional means of notifying
an operations system (OS) maintenance center of environmental conditions at the
OLS site.

Releases 1.0, 2.0, 2.1, and 3.0 do not support use of the Ser Tlm 2 port (P20).

Available WaveStar OLS 40G Serial Telemetry Cables

Table 5-4 lists available cables for serial telemetry applications

Table 5-4.

WaveStar OLS 40G Serial Telemetry Cables

Table 5-5 lists serial telemetry cable connection to the interconnection panel.

(Continued on next page)

ED-7G028-22
Cable Group

Cable Length (ft.)

201

As required(4000’ max.)

251

150

261

250

«
...
168
169
170
171
172
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды