Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 43

Issue 1.0

March 2001

1-11

365-575-389

Installation Manual

Overall Installation and Test Considerations

Safety Instructions (Continued)

Lightwave Safety
(continued)

Lasers and laser products are subject to federal and state regulations as well as
Lucent Technologies laser safety requirements. The WaveStar OLS 40G uses a
Class I or Class IIIb laser as a transmitter. Under normal operation, the system is
totally enclosed and fully protected by devices such that it presents no hazards to
safety or health. Each system has been certified and registered with the National
Center for Devices and Radiological Health (NCDRH) under the U.S.Food and
Drug Administration (FDA) as a Class I system (exempt lasers and laser
systems). All sections of the WaveStar OLS 40G that can be removed and allow
potential access to laser radiation have been identified. A warning label is
provided on the rear of the shelf.

For safety reasons, the equipment comes with the Automatic Power Shutdown
(APSD) feature enabled for optical amplifiers (OAs)

!

DANGER:

Disabling the Automatic Power Shutdown (APSD) feature results in a FDA/
IEC Class IIIb/3B laser hazard. APSD is a safety feature. Do not attempt to
defeat or disable APSD. Defeating APSD may result in harm to personnel
exposed to disconnected or cut optical fibers.

!

CAUTION:

To comply with IEC regulations, systems containing an IEC Class 3B laser
hazard must be installed in a controlled environment. Please refer to
applicable IEC standards.

In addition, a compliance label stating that the system has been certified, along
with the manufacturer’s name and place of manufacture, is attached to each
equipment bay. The compliance label is located on the rear of the equipment
bays. Several Cautions, Notices and Danger Indications are also given on the rear
label. Be sure to read and observe them. The text in these labels now appears in
both French and English for an international market.

(Continued on next page)

«
...
41
42
43
44
45
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды