manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 561

Issue 1.0

March 2001

G-3

365-575-389

Installation Manual

Related Equipment

Overview (Continued)

Dantel Orderwire 
(continued)

The data circuit works as follows:

1.

Select channel 1 on the 41096 orderwire panel, then pick up the handset 
and call the remote terminal (station 2 code).

At the remote end, the 00330 orderwire terminal pack answers the call and 
operates an M lead driver that opens a communications channel through 
the 44202 202 Compatible Modem pack.

2.

Select both channels 1 and 2 on the 41096 panel. This connects the 
computer and external modem to the system. At the same time, the optical 
coupler (OC) circuit disables the side tone in the 00330 orderwire terminal 
so that the modem does not receive its own data.

3.

Hang up the handset and start sending or receiving digital data.

4.

When done, press the # key to disconnect the modem at the remote 
terminal. Release the channel 2 pushbutton. The channel 2 button can be 
released or left pushed in since it is used for both voice and data 
communications.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды