Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 476 | Manualshive

Страница: 476 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 476

11-4

Issue 1.0

March 2001

365-575-389

Installation Manual

Connecting SONET/SDH Systems to WaveStar OLS
40G

Background (Continued)

LBO Information
(continued)

A wide variety of LBOs are available for Release 2.1 and subsequent releases. A
family of Green-colored single-mode to single-mode LBOs designed for 1550 nm
with higher power capability is available. To handle the transition from single-mode
to multi-mode, another family of LBOs was developed and is Gray colored. All
inputs to OTPMs must use this Gray LBO.

Refer to Appendix I to obtain tolerances, power ratings, and further data on LBOs.

OTU and OTPM
Information

41-Type OTUs

The 41A(1-16)-type, 41C(1-16)-type, and 41D(1-16)-type Optical Translator Units
(OTU) receive an OC-48 optical signal at its input, downconverts the signal to a
2.5-Gb/s electrical signal, strips away stray tones caused by intermodulation
products, applies a new tone at a code specific frequency, upconverts to an
optical signal, and outputs an WaveStar OLS 40G compatible OC-48 optical
signal at a wavelength specified by its particular code.

The 41F(1-16) type OTU enables Gigabit Ethernet (1-Gb Ethernet) signals to be
transmitted on the 40G system. All OTUs can receive optical signals in the 1310-
nm and 1550-nm range.

OTUs may be used to regenerate the optical signal or provide Wavelength Add
Drop (WAD) capability. The 41B-type, 41E-type and 41G-type OTU translate a
1550-nm signal to a 13100-nm signal for compatibility with 1310-nm equipment.

For additional information on the 41-type OTUs, refer to the Applications,
Planning, and Ordering Guide (365-575-386).

42-Type OTPMs

Each of these Optical Translator Port Modules (OTPM) electrically regenerates a
single input OC-12/STM-4 optical signal and inserts the tone required by
WaveStar OLS 40G onto that signal. The sixteen 42Ax OTPM codes support the
sixteen 1500 nm wavelengths on WaveStar OLS 40G systems with a total
dispersion not exceeding 10,900 ps/nm.

This type of OTPM accepts any OC-12/STM-4 wavelength in the 1280-1335 nm
or 1480- to 1580-nm range and converts it to an electrical STS-12 signal. The
electrical STS-12 signal is reshaped, retimed, and amplified.

(Continued on next page)

«
...
474
475
476
477
478
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды