manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 520

C-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Fiber Cleaning

Background

Introduction

This procedure describes the Lucent recommended method for the cleaning and 
inspection of optical connectors using specific tools and materials that have been 
proven to be effective in the assembly and testing of optical transmission 
equipment. It is critical that the connector endfaces are clean and free from 
particular contamination to assure proper performance and reliability of lightwave 
systems. With the modern high speed, high power and wider bandwidth optical 
transmission systems, clean connectors along the optical path are absolutely 
essential for successful operation.

Objectives

This chapter provides information to perform the following:

1.

Properly clean an optical connector

2.

Inspect an optical connector for cleanliness

Related 
Information

A course on connector cleaning and the connector inspection process is now 
offered through Lucent Technologies Learning and Performance Center, Course 
Code: LMC214H “Understanding Fiber Optic Cleaning, Inspection and Testing.” 
To learn more about this course, consult your local Lucent Account 
Representative.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды