manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 431

Issue 1.0

March 2001

9-41

365-575-389

Installation Manual

Local Installation Testing

Final Testing of OTU Circuit Packs 
(Continued)

Final Test 
Procedures

Perform the following steps to final test the OTU/OTPMs:

(Continued on next page)

Step

Action

Reference

1 

Obtain an appropriate signal from the associated 
SONET/SDH transmission equipment or a SONET/SDH 
test set. Verify with an optical power meter that the 
source is within the input specification of the OTU/OTPM 
(–27 to –11 dBm).

2 

Connect the signal to the input of the first OTU/OTPM to 
be checked. Connect an optical power meter to the 
OTU/OTPM output using a fiber jumper with appropriate 
connectors.
Requirement: The output power from the OTU/OTPM 
Code shall be between the minimum and maximum 
power specified in Table 9-6 on page 9-42 and the fault 
LED shall be OFF.

Table 9-6 on 
page 9-42

3 

If the 506B OMU is being used, the incoming channels 
must be balanced. Connect the output signal of the 
OTU/OTPM which still has the test set on it from Step 2 
to the correct OCHAN IN port of the OMU. Connect an 
optical power meter or optical multi-wavelength meter to 
the OMU OUT port. 

Requirement: The per-channel output power of the 
OMU should be -21 dBm.

If the Requirement is not met, adjust the LC LBO on the 
OCHAN IN port of the OMU.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды