Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 578

Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 238

6-10

Issue 1.0

March 2001

365-575-389

Installation Manual

WaveStar OLS 40G Fiber and Circuit Pack Installation

Generic Information for Fiber
Installation (Continued)

Circuit Pack
Installation

Circuit pack installation for the WaveStar OLS 40G includes the following:

■

Install, but do not seat, all circuit packs and units in their final locations to
aid in the installation of the fiber jumpers.

■

After software installation in

Chapter 9, Local Installation Testing

, the circuit

packs will be moved to their final locations.

General Circuit Pack Installation Considerations

■

A wrist strap, connected to the wrist strap ground jack on the user panel or
filter panel, must be worn when handling circuit packs or touching the
terminal.

■

Circuit packs are keyed to prevent being inserted into the wrong shelf
position.

■

Before installing any circuit packs, inspect the circuit pack side of the
backplane for any bent or broken backplane pins. If any pins are found to
be bent, straighten the pin if possible.

■

Any broken pins or bent pins that cannot be straightened must be replaced
using the BERG MT370-01 pin kit for the METRAL pins, or the KS-22876
L6 Pin Repair Kit for the FASTECH technology. Refer to

Appendix B, Pin

Repair

■

When installing circuit packs, use care to insert them straight to avoid
damaging the circuit packs or the backplane pins.

■

Fiber connectors on optical circuit packs should always be either
connected to fiber or covered by protective covers.

!

CAUTION:

No fiber jumpers shall be connected to the circuit packs or units at this time.
Do not connect the fiber jumpers until instructed to do so.

NOTE:

The 41-type OTUs are keyed the same as the Optical Amplifiers (OAs).
However the OTUs have more depth and cannot be fully inserted into the
shelf. Do Not attempt to seat an OTU into an Optical Amplifier slot.

(Continued on next page)

«
...
236
237
238
239
240
...
»

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды