manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 41

Issue 1.0

March 2001

1-9

365-575-389

Installation Manual

Overall Installation and Test Considerations

Safety Instructions

Admonishments

This manual contains admonishments in the form of DANGERS, WARNINGS, 
and CAUTIONS. These admonishments, listed in order of priority, have the 
following definitions: 

■

Danger shows the presence of a hazard that will cause death or severe 
personal injury if the hazard is not avoided. 

■

Warning shows the presence of a hazard that can cause death or severe 
personal injury if the hazard is not avoided. 

■

Caution shows the presence of a hazard that will or can cause minor 
personal injury or property damage if the hazard is not avoided. Caution is 
also used for property-damage-only accidents. This includes equipment 
damage, loss of software, or service interruption. 

These admonishments are noted by an alert symbol 

.

IMPORTANT 
SAFETY 
INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS. 

When using this telecommunication equipment, basic safety precautions should 
always be followed to reduce the risk of fire, electric shock, and injury to persons, 
including the following: 

1.

Follow all warnings and instructions marked on the product. 

2.

Slots and openings in this product at the back or bottom are provided for 
ventilation. To protect the product from overheating, these openings must 
not be blocked or covered. 

3.

Opening or removing rear covers or sheet metal parts may present 
exposure to high current or electrical energy levels or to other risks.

4.

Never push objects of any kind into this product through slots as they may 
touch dangerous voltage points or short out parts that could result in a risk 
of fire or electrical shock. Never spill liquid of any kind on the product. 

5.

Refer servicing to qualified service personnel. 

6.

Use caution when installing and modifying telecommunications lines.

7.

Never install telecommunication wiring during a lightning storm.

8.

Never install telecommunication jacks in wet locations unless the jack is 
specifically designed for wet locations.

(Continued on next page)

!

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды