manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 540

D-10

Issue 1.0

March 2001

365-575-389

Installation Manual

CMC Dantel Alarm and Control Block Installation, 
Extended Miscellaneous Discretes

Provisioning Extended Miscellaneous 
Discretes

Enabling SER 
TLM 1 Port

The SER TLM Port must first be enabled through the CMC by using the following 
Command:

■

SECURITY-ENTER-Channel Identifier-Security, AID=SER_TLM1, PORT 
ACC=enable

Extended 
Miscellaneous 
Discrete 
Assignments

The Miscellaneous Discrete Assignments are provisioned by using the following 
command through the CMC:

CONFIGURATION_Set_Attribute_Enviroment_

This input sets the Descriptions and Alarm Levels for the miscellaneous discrete 
inputs.

■

The Point parameter selects the miscellaneous discrete input point to 
provision

NOTE:

The miscellaneous discrete points 1-16 are assigned to the original 
miscellaneous discrete ports. Therefore the extended miscellaneous 
discretes will begin their assignment with point number 17 and continue 
through point number 144.

■

The Alarm Level Parameter provisions the severity of the condition 
associated with the closing of the selected miscellaneous discrete input 
point. The choices are:

— "CR": critical

— "MJ": major

— "MN": minor

— "NA": status not alarmed

— "NR": status not alarmed and not reported to the OS.

The Description parameter is the text string associated with the selected 
miscellaneous discrete environmental input point. It is character string of up to 26 
characters, where the characters are letters, digits, or spaces. It is used to identify 
the point in the FAULT-RETREIVE-LOG and FAULT-RETREIVE-ALARMS

 

reports.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды