manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 368

8-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Network Element Startup and Provisioning

Background

Introduction

This section describes procedures to:

n

Install software into the SYSMEM circuit pack of the WaveStar

TM 

OLS 40G 

Network Element

n

Install circuit packs into the Network Element

n

Perform basic provisioning of the Network Element so that installation 
testing can be performed

NOTE:

It is assumed that the installer is familiar with the personal computer and its 
use as a CenterLink Console Manager. If instruction in this area is needed, 
refer to the R7 Software Release Description C109074484 for information 
including: performing software installation, setting up a PC for use with the 
WaveStar OLS 40G, and logging in to the system using a CMC (CenterLink 
Management Console) PC. More information is also available in the 
WaveStar OLS 40G User/Service Manual (365-575-387).

General 
Considerations

Note the following before starting: 

n

Disconnect the office alarms from the Network Element before performing 
any tests. Reconnect the office alarms after completing the testing. 

n

Required equipment is given in Section 1 of this document. Essential 
equipment for this section is: one personal computer (PC) with CMC 
software for use as CenterLink Management Console and connecting 
cable.

Tools, Test Sets, 
and Accessories 

The following equipment is required to complete the procedures in this section:

n

Wrist strap connected to the wrist strap ground jack of the user panel for 
ESD protection.

n

A CD-ROM of Release 7-WaveStar OLS 40G network software and CMC. 

n

Personal computer for use as CMC. 

(Continued on next page)

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды