manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 474

11-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Connecting SONET/SDH Systems to WaveStar OLS 
40G

Background

Introduction

This chapter covers fiber jumper installation and testing between SONET/SDH 
Systems and the WaveStar Optical Line System (OLS) 40G at the OLS End 
Terminal offices.

!

CAUTION:

Procedures in this installation manual are only to be performed by trained 
personnel.

General 
Considerations

!

WARNING:

Unterminated optical connectors may emit laser radiation and should not be 
viewed with optical instruments other than indirect image-converting 
devices. Also, avoid direct exposure to beam.

Keep the following information under consideration during cable installation:

■

Do not use cable ties with the optical fiber.

■

Place optical fiber jumpers in protective tube or channel, such as the 
polyvinyl chloride (PVC) tubing provided in the installation kit 
(C848065959) when running the cable from the WaveStar OLS 40G to the 
cable rack.

■

Place optical fiber jumpers in the cable rack in a protective channel with 
nothing on top of them.

■

Maintain a minimum of 1.5 inches of optical fiber bend radius.

■

Optical fiber jumpers require ST, FC/PC, LC, or SC type connectors for 
connection to the WaveStar OLS 40G.

(Continued on next page)

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды