manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 574

I-2

Issue 1.0

March 2001

365-575-389

Installation Manual

Line Buildout (LBO)

Overview

Description

The Lucent Technologies Line Buildouts (LBOs) provide an optical transition from 
the circuit pack output block to a standard optical connector. The WaveStar OLS 
40G circuit packs utilize the Universal type output block and the LBOs referred to 
here are those that transition from a Universal block to a standard optical 
connector. In addition to providing a transition, the line buildouts or LBOs can 
provide from zero to 20 dB of attenuation as an in-line attenuator.

Prior to the development of the WaveStar OLS 40G, there were a few basic 
variations in LBOs. With the development of the WaveStar OLS 40G, new 
demands were placed upon LBOs for improved attenuation tolerances, higher 
power levels, additional granularity, and single-mode to multimode transitions. 
This has created several new designs with different properties and applications. 
The purpose of this Appendix will be to provide the specifications and suggest 
applications for each LBO type.

There are four basic types of LBOs used with WaveStar OLS 40G and they are 
identified by the colors white or blue, yellow, green, and gray. Each LBO has its 
attenuation value printed in black numerals on its side. Once the LBO has been 
removed from its shipping bag, its type can only be identified by its color. In the 
field, the distance between the LBO and its shipping bag and the time since 
separation is both large and long for this small device. Thus the emphasis on color 
identification.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды