manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 477

Issue 1.0

March 2001

11-5

365-575-389

Installation Manual

Connecting SONET/SDH Systems to WaveStar OLS 
40G

Background (Continued)

OTU and OTPM 
Information 
(continued)

The 42B OTPM circuit pack generates a OC-12/STM-4 signal in the 1330-nm 
range for other OC-12/STM-4 receivers. For detailed information, refer to the 
APOG (365-575-386).

43-Type OTPMs

Each of these Optical Translator Port Modules (OTPM) electrically regenerates a 
single input OC-3/STM-1 optical signal and inserts the tone required by WaveStar 
OLS 40G onto that signal. The sixteen 43Ax OTPM codes support the 1550-nm 
wavelengths on the WaveStar OLS 40G systems with total dispersion not 
exceeding 10,900 ps/nm.

This type of OTPM accepts any OC-3/STM-1 wavelength in the 1280-1335 nm or 
1480- to 1580-nm range and converts it to an electrical STS-3 signal. The 
electrical STS-3 signal is reshaped, retimed, and amplified.

The 43B OTPM circuit pack generates an OC-3/STM-1 signal in the 1330-nm 
range for other OC-3/STM-1 receivers. For detailed information associated with 
the 43A and 43B OTPM circuit packs, refer to the APOG (365-575-386).

44-Type OTPMs

Each of these Low-Speed Broadband (LSBB) Optical Translator Port Modules 
(OTPM) accepts any OC-3/STM-1, OC-12/STM-4, or 100-750 Mb/s optical signal, 
converts it to an electrical signal, amplifies the signal, inserts an identification tone 
required by WaveStar OLS 40G and produces the code specified optical output. 
The sixteen 44Ax OTPM codes support the 1500-nm wavelengths on the 
WaveStar OLS 40G systems with a total dispersion not exceeding 10,900 ps/nm. 

The 44B OTPM circuit pack generates an OC-3/STM-1, OC-12/STM-4, or 100-
750 Mb/s signal in the 1330 nm range for other receivers. For additional 
information regarding 44-type OTPMs, refer to the APOG (365-575-386).

The LSBB OTPMs do not perform clock recovery on their input data stream and 
hence have no way to control jitter accumulation. The LSBB OTPMs should not 
be used to concatenate WaveStar OLS 40G systems. Signals entering an end 
terminal from an LSBB OTPM must be dropped at the next end terminal.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды