manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 230

6-2

Issue 1.0

March 2001

365-575-389

Installation Manual

WaveStar OLS 40G Fiber and Circuit Pack Installation

Background

Introduction

!

CAUTION:

Procedures in this installation manual are only to be performed by trained 
personnel.

This chapter covers WaveStar OLS 40G and OT and gives a brief overview of 
each piece of equipment. It is broken into the 11 sections listed below.

■

Generic Information for Fiber Installation

■

1A-TX End Terminal Specific Installation

■

1A-RCV End Terminal Specific Installation

■

Repeater Terminal Specific Installation

■

One OA 1A-TX End Terminal Specific Installation

■

One OA 1A-RCV End Terminal Specific Installation

■

Two OA/Two OA Dual Facing Shelf Installation

■

Two OA/One OA Dual Facing Shelf Installation

■

One OA/Two OA Dual Facing Shelf Installation

■

One OA/One OA Dual Facing Shelf Installation

■

Rack and Stack Configuration Installation

■

OT Specific Installation

■

Rack and Stack Configurations

■

Telemetry Feed-Through Installation

All sections except for the Generic Information for Fiber Installation cover fiber 
routing, fiber protection, fiber dressing, circuit pack and unit installation and 
precautions, and fiber installation.

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды