manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 330

6-102

Issue 1.0

March 2001

365-575-389

Installation Manual

WaveStar OLS 40G Fiber and Circuit Pack Installation

Rack and Stack Configuration 
(Continued)

Fiber Jumper 
Installation

There are several different fiber jumper kits available for the rack and stack 
systems, some of which include blue fiber jumpers. These blue jumpers are 
standard single mode jumpers whose outer protective cover has been colored 
blue to indicate to all personnel that the fiber is carrying high-speed traffic, up to 
16 channels of 2.5 Gigabits (40Gbits) of data/voice. 

The fiber labels that are to be used are the following:

The three sets of labels are all included in each of the fiber jumper kits. The kits, 
their comcodes, and contents are listed below. See drawing NT00405-30 for 
further details.

Two-Bay Rack and Stack Fiber Kits

For a two-bay Rack and Stack configuration, the following fiber kits (Kits 1, 2, and 
5) will be needed for Line 1:

(Continued on next page)

Comcode

Description

847740495

Labels for internal OLS fiber connections

847740503

Labels for OT channels 1-8

848027694

Labels for OT channels 9-16

Kit Comcode 

and Desc.

Item 

Qty.

Item Comcode

Item Description

Length

108993502

Kit # 2

Line 1 fibers for 
OA/ODU/OMU 
connections

Blue fibers

1

108845819

MSB1LC-SC

1.67 FT

2

108845793

MSB1LC-SC

4.17 FT

2

108845801

MSB1SC-SC

4.17 FT

1

108989609

MSB1LC-SC

7 FT

1

108989633

MSB1SC-SC

12 FT

1

108989641

MSB1SC-SC

13 FT

1

847740495

Labels for OLS packs

1

847740503

Labels for OT channels 1-8

1

848027694

Labels for OT channels 9-16

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды