manualshive.com logo in svg

Texas Instruments TMS570LC4357, Technical Reference Manual

The Texas Instruments TMS570LC4357 Technical Reference Manual is a comprehensive guide for users looking to maximize the capabilities of their product. This manual can be downloaded for free from manualshive.com, offering detailed instructions and specifications to enhance the user experience and optimize performance.

Share
Download
background image

www.ti.com

Peripheral Interconnect Subsystem

267

SPNU563A – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

Interconnect

4.2.1 Accessing PCRx and CRCx Slave

System peripherals can be accessed via the PCR1 slave port. User peripherals can be accessed via
either the PCR2 or PCR3 slave ports. Refer to the datasheet for information on what peripherals are
available through each PCR. Peripheral Central Resource (PCR) is responsible to further decode the
slave address to select the desired peripheral.

There are two CRC modules implemented in the device. Both are direct slaves to the Peripheral
Interconnect Subsystem.

4.2.2 Accessing SDC MMR Port Slave

Safety Diagnostic Controller (SDC) MMR Port is a slave to the Peripheral Interconnect Subsystem to
access the safety diagnostic related control and status registers of the CPU Interconnect Subsystem.

Table 4-2

lists the CPU Interconnect Subsystem SDC register bit field mapping.

Table 4-2. CPU Interconnect Subsystem SDC Register Bit Field Mapping

Register Name

Bit 0

Bit 1

Bit 2

Bit 3

Bit 4

Bit 5

Bit 6

Remark

ERR_GENERIC_

PARITY

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Each bit indicates the
transaction processing block
inside the interconnect
corresponding to the master
that is detected by the
interconnect checker to have a
fault.
Error related to parity
mismatch in the incoming
address.

ERR_UNEXPECTED_

TRANS

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Error related to unexpected
transaction sent by the master.

ERR_TRANS_ID

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Error related to mismatch on
the transaction ID.

ERR_TRANS_

SIGNATURE

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Error related to mismatch on
the transaction signature.

ERR_TRANS_TYPE

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Error related to mismatch on
the transaction type.

ERR_USER_PARITY

PS_SCR_

M

POM

DMA_

PORTA

CPU

AXI-M

Reserved

ACP-M

Reserved

Error related to mismatch on
the parity.

SERR_UNEXPECTED_

MID

L2 SRAM

Wrapper

L2 Flash
Wrapper

Port A

L2 Flash
Wrapper

Port B

EMIF

Reserved

CPU

AXi-S

ACP-S

Each bit indicates the
transaction processing block
inside the interconnect
corresponding to the slave that
is detected by the interconnect
checker to have a fault.
Error related to mismatch on
the master ID.

SERR_ADDR_

DECODE

L2 SRAM

Wrapper

L2 Flash
Wrapper

Port A

L2 Flash
Wrapper

Port B

EMIF

Reserved

CPU

AXi-S

ACP-S

Error related to mismatch on
the most significant address
bits.

SERR_USER_PARITY

L2 SRAM

Wrapper

L2 Flash
Wrapper

Port A

L2 Flash
Wrapper

Port B

EMIF

Reserved

CPU

AXi-S

ACP-S

Error related to mismatch on
the parity of the most
significant address bits.

4.2.3 Accessing Other Slaves via PS_SCR_S

In order for some of the masters connected to the Peripheral Interconnect Subsystem to access the slaves
such as L2 Flash and L2 SRAM in the CPU Interconnect Subsystem, their requests are first funneled into
the PS_SCR_S slave where it then becomes a master on the CPU Interconnect Subsystem as
PS_SCR_M. The request appearing on the PS_SCR_M is then decoded and routed to the intended slave
by the CPU Interconnect Subsystem.

Summary of Contents for TMS570LC4357

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS570LC4357

Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Brand: Warren Controls Pages: 16
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Brand: Federal Signal Corporation Pages: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Brand: FASTRON. Pages: 16
National Instruments PXI-8231 Installation Manual preview
PXI-8231
Brand: National Instruments Pages: 6
Vageo DT-1 Plus Manual preview
DT-1 Plus
Brand: Vageo Pages: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Brand: Vacon Pages: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Brand: Vacon Pages: 24
Vacon 100X series Marine Installation Manual preview
100X series
Brand: Vacon Pages: 30
Vacon 100 flow User Manual preview
100 flow
Brand: Vacon Pages: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Brand: Vacon Pages: 100
Linear Technology LT8570 Demo Manual preview
LT8570
Brand: Linear Technology Pages: 7
YASKAWA J1000 CIMR-JC series Installation Manual preview
J1000 CIMR-JC series
Brand: YASKAWA Pages: 25
mikroElektronika ETH WIZ click Quick Start Manual preview
ETH WIZ click
Brand: mikroElektronika Pages: 3
Window Master WMU 831 Installation Instructions Manual preview
WMU 831
Brand: Window Master Pages: 7
Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Brand: Objective Imaging Pages: 11
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Brand: HANYOUNG NUX Pages: 4
Kelly KLS2418ND User Manual preview
KLS2418ND
Brand: Kelly Pages: 37
Velp Scientifica F201A0505 Instruction Manual preview
F201A0505
Brand: Velp Scientifica Pages: 24

Brands by name

Popular brands

Load more brands