manualshive.com logo in svg

Texas Instruments TMS570LC4357, Technical Reference Manual

The Texas Instruments TMS570LC4357 Technical Reference Manual is a comprehensive guide for users looking to maximize the capabilities of their product. This manual can be downloaded for free from manualshive.com, offering detailed instructions and specifications to enhance the user experience and optimize performance.

Share
Download
background image

www.ti.com

HTU Control Registers

1171

SPNU563A – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

High-End Timer Transfer Unit (HTU) Module

Table 24-39. Memory Protection Control and Status Register (HTU MPCS) Field Descriptions (continued)

Bit

Field

Value

Description

15-12

Reserved

0

Reads return 0. Writes have no effect.

11-8

CPNUM1

Control Packet Number for single memory protection region configuration. CPNUM1 holds the number
of the CP, which has caused the first memory protection error when only one memory protection region
is used. This number is not updated for multiple access violations until it is read by the CPU. During
debug mode, CPNUM1 is frozen even when read.

0

CP A of DCP0

1h

CP B of DCP0

2h

CP A of DCP1

3h

CP B of DCP1

4h

CP A of DCP2

5h

CP B of DCP2

6h

CP A of DCP3

7h

CP B of DCP3

8h

CP A of DCP4

9h

CP B of DCP4

Ah

CP A of DCP5

Bh

CP B of DCP5

Ch

CP A of DCP6

Dh

CP B of DCP6

Eh

CP A of DCP7

Fh

CP B of DCP7

7-6

Reserved

0

Reads return 0. Writes have no effect.

5

INTENA01

Interrupt Enable 01. This bit needs to be set when working with two memory-mapped regions and a
error should be generated to the ESM module on an access violation.

0

Error signaling is disabled.

1

Error signaling is enabled.

4

ACCR01

Access Rights 01. This bit defines the access rights for the HTU for accesses outside the region defined
by the MP0S and MP0E and the MP1S and MP1E registers.

0

HTU read access is allowed but write access will be signaled.

1

Any access performed by the HTU is forbidden and will be signaled.

3

REG01ENA

Region Enable 01. This bit needs to be set when working with two memory-mapped regions.

REG0ENA

must be cleared to 0

if this bit is set to a 1. Memory region 0 must be less than memory region 1.

0

The protection outside the memory region defined by the MP0S and MP0E and the MP1S and MP1E
registers is not enabled. This means the HTU can access any implemented memory space. REG0ENA
could still enabled to give protection outside the MP0S:MP0E region.

1

The protection outside the memory region defined by the MP0S and MP0E and the MP1S and MP1E
registers is enabled. This means the HTU can perform any access within the regions, but if it attempts
to perform a forbidden access outside of both of the regions (according to the ACCR01 configuration),
the access is signaled by the MPEFT1 flag. The number of the CP, which has caused the memory
protection error, is captured to CPNUM1 if it is not currently frozen and an error is generated if it is
enabled.

2

INTENA0

Interrupt Enable 0. This bit needs to be set when working with one memory-mapped region and a error
should be generated to the ESM module on an access violation.

0

Error signaling is disabled.

1

Error signaling is enabled.

1

ACCR

Access Rights 0. This bit defines the access rights for the HTU for accesses outside the region defined
by the MP0S and MP0E registers for a single memory protection region configuration.

0

HTU read access is allowed but write access will be signaled.

1

Any access performed by the HTU is forbidden and will be signaled.

Summary of Contents for TMS570LC4357

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS570LC4357

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Brand: Eaton Pages: 16
Koer C35CBMS Manual preview
C35CBMS
Brand: Koer Pages: 6
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
Shimaden SR80 Series Instruction Manual preview
SR80 Series
Brand: Shimaden Pages: 16
Patton SmartNode 5501 User Manual preview
SmartNode 5501
Brand: Patton Pages: 56
D-M-E VCTB-4000 User Manual preview
VCTB-4000
Brand: D-M-E Pages: 15
Alcor Micro AU9540 Technical Reference Manual preview
AU9540
Brand: Alcor Micro Pages: 18
Abov A96G140 User Manual preview
A96G140
Brand: Abov Pages: 278
Zennio MAXinBOX66 Technical Documentation preview
MAXinBOX66
Brand: Zennio Pages: 2
FAAC RESIST TPS SA Manual preview
RESIST TPS SA
Brand: FAAC Pages: 3
Hanna Instruments BL121 Manual preview
BL121
Brand: Hanna Instruments Pages: 44
Digital Acoustics IP7-MZC-FD Application Manual preview
IP7-MZC-FD
Brand: Digital Acoustics Pages: 7
Dasko Electronic DSS2 T-BIS_P Manual preview
DSS2 T-BIS_P
Brand: Dasko Electronic Pages: 4
Taco Electronic Solutions iWorx ZXU1 Installation Manual preview
iWorx ZXU1
Brand: Taco Electronic Solutions Pages: 24
Carrera GO!!! Plus Operating Instructions preview
GO!!! Plus
Brand: Carrera Pages: 3
Qanon VDA14 Manual preview
VDA14
Brand: Qanon Pages: 10
Adaptec ACB-2070A Installation Manual preview
ACB-2070A
Brand: Adaptec Pages: 7
EMUS BMS Mini User Manual preview
BMS Mini
Brand: EMUS Pages: 36

Brands by name

Popular brands

Load more brands