NEC V850E/MA1 User Manual Download Page 331

Page: 331 / 567

CHAPTER 10 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

User’s Manual U14359EJ4V0UM

331

(2) Timer mode control registers C01 to C31 (TMCC01 to TMCC31)

The TMCCn1 registers control the operation of TMCn (n = 0 to 3).

These registers can be read or written in 8-bit units.

Be sure to set bit 2 to 0. If it is set to 1, the operation is not guaranteed.

Cautions 1. The various bits of the TMCCn1 register must not be changed during timer operation. If

they are to be changed, they must be changed after setting the TMCCEn bit of the

TMCCn0 register to 0. If these bits are overwritten during timer operation, operation

cannot be guaranteed (n = 0 to 3).

2. If the ENTn1 and ACTLVn bits are changed at the same time, a glitch (spike shaped

noise) may be generated in the TO0n pin output. Either create a circuit configuration

that will not malfunction even if a glitch is generated or make sure that the ENTn1 and

ACTLVn bits do not change at the same time (n = 0 to 3).

3. TO0n output is not changed by an external interrupt signal (INTP0n0 or INTP0n1). To

use the TO0n signal, specify that the capture/compare registers are compare registers

(CMSn0 and CMSn1 bits of TMCCn1 register = 1) (n = 0 to 3).

(1/2)

Address

After reset

TMCC01

OST0

ENT01

ACTLV0

ETI0

CCLR0

CMS01

CMS00

FFFFF608H

20H

TMCC11

OST1

ENT11

ACTLV1

ETI1

CCLR1

CMS11

CMS10

FFFFF618H

20H

TMCC21

OST2

ENT21

ACTLV2

ETI2

CCLR2

CMS21

CMS20

FFFFF628H

20H

TMCC31

OST3

ENT31

ACTLV3

ETI3

CCLR3

CMS31

CMS30

FFFFF638H

20H

Bit position

Bit name

Function

OSTn

(n = 0 to 3)

Overflow Stop

Sets the operation when TMCn has overflowed (n = 0 to 3).

0: After the overflow, counting continues (free-running mode)

1: After the overflow, the timer maintains the value 0000H, and counting stops

(overflow stop mode). At this time, the TMCCEn bit of TMCCn0 remains at 1.

Counting is restarted by writing 1 to the TMCCEn bit.

ENTn1

(n = 0 to 3)

Enable To Pin

External pulse output is enabled/disabled (TO0n) (n = 0 to 3).

0: External pulse output is disabled. Output of the ACTLVn bit inactive level to

the TO0n pin is fixed. The TO0n pin level is not changed even if a match

signal from the corresponding compare register is generated.

1: External pulse output is enabled. A compare register match causes TO0n

output to change. However, if capture mode is set, TO0n output does not

change. The ACTLVn bit inactive level is output from the time when timer

output is enabled until a match signal is first generated.

Caution If either CCCn0 or CCCn1 is specified as a capture register, the

ENTn1 bit must be set to 0.

Summary of Contents for V850E/MA1
























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands

NEC V850E/MA1, User Manual

Search results

Summary of Contents for V850E/MA1

Reviews:

Related manuals for V850E/MA1

Brands by name

Popular brands