manualshive.com logo in svg

NEC V850E/Dx3, Preliminary User'S Manual


Share
Download
background image

173

Clock Generator

Chapter 4

Preliminary User’s Manual U17566EE1V2UM00

(5)

STOP mode

In STOP mode, all clock sources are stopped, except sub and ring oscillator. 
These can be configured in register WCC to stop as well. No clock is available, 
and no internal self-timed processes operates.

The STOP mode can be released by

• the unmasked maskable interrupts INTPn, INTCnWUP, INTVCn, INTCBnR

• NMI0, NMIWDT

• RESET, RESPOC, RESWDT, RESCMM, RESCMS

On STOP mode release, the CPU clock and peripheral clocks are supplied by 
the main oscillator.

(6)

Clock status summary

Table 4-29 on page 174

 summarizes the status of all clocks delivered by the 

Clock Generator in the different states.

“Normal” describes all status except reset and power save modes.

The HALT mode is not listed in the table. It does not change any of the table 
items, but stoppes only the CPU core operation.

Below the table you find the explanation of the terms used in the table.

Table 4-28

Clock Generator status in STOP mode

Item

Status

Remark

Main oscillator

stopped

Sub oscillator

operates/stopped

Stopped if WCC.SOSTP = 1

Ring oscillator

operates/stopped

Stopped if WCC.ROSTP = 1

SSCG

stopped

PLL

stopped

VBCLK (CPU system)

stopped

IICLK

stopped

PCLK0, PCLK1

stopped

PCLK2…PCLK15

stopped

SPCLK0, SPCLK1

stopped

SPCLK2…SPCLK15

stopped

FOUTCLK

stopped

WTCLK / LCDCLK

stopped

WDTCLK

unchanged/stopped

Stopped, if the selected clock 
source stops

WCTCLK

stopped

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Summary of Contents for V850E/Dx3



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V850E/Dx3

Paratec TE Series User Manual preview
TE Series
Brand: Paratec Pages: 8
J+J S2 Handbook preview
S2
Brand: J+J Pages: 33
Cadac 343 User Instructions preview
343
Brand: Cadac Pages: 4
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Brand: Webasto Pages: 8
Meilhaus Electronic USB-GT Manual preview
USB-GT
Brand: Meilhaus Electronic Pages: 19
M-Audio Keystation 61es User Manual preview
Keystation 61es
Brand: M-Audio Pages: 15
Webasto Thermo Call TC3 Installation Instructions Manual preview
Thermo Call TC3
Brand: Webasto Pages: 15
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Brand: Aqua Lung Pages: 18
Arbor Technology ARES-1231 Series User Manual preview
ARES-1231 Series
Brand: Arbor Technology Pages: 94
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Brand: Danfoss Pages: 2
PXM PX268 User Manual preview
PX268
Brand: PXM Pages: 10
VisAccess VXS-5 Installation Instructions preview
VXS-5
Brand: VisAccess Pages: 3
Belimo LRB24-SR-T Wiring Diagrams preview
LRB24-SR-T
Brand: Belimo Pages: 2
NXP Semiconductors P89LPC952 User Manual preview
P89LPC952
Brand: NXP Semiconductors Pages: 134
jablotron GD-06 ALLEGRO Manual preview
GD-06 ALLEGRO
Brand: jablotron Pages: 2
CYCLOPS NOVA OSD Manual preview
NOVA OSD
Brand: CYCLOPS Pages: 10
NHRC NHRC-10 User Manual preview
NHRC-10
Brand: NHRC Pages: 104
Zennio MINiBOX 0-10V X3 User Manual preview
MINiBOX 0-10V X3
Brand: Zennio Pages: 25

Brands by name

Popular brands

Load more brands