Fuji Electric FRENIC-AQUA series, User Manual

Page: 293 / 751

6-12
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
C58 Analog Input Adjustment for Terminal [12]
(Display unit)
1: none
2: %
4: r/min
7: kW
Flowrate
20: m
3
/s
21: m
3
/min
22: m
3
/h
23: L/s
24: L/min
25: L/h
Pressure
40: Pa
41: kPa
42: MPa
43: mbar
44: bar
45: mmHg
46: psi (Pound per square inch)
47: mWG
48: inWG
Temperature
60: K
61: °C
62: °F
Density
80: ppm
Y Y 2
C59 (Maximum scale) -999.00 to 0.00 to 9990.00
N Y 100
C60 (Minimum scale) -999.00 to 0.00 to 9990.00 N Y 0.00
C61 Analog Input Adjustment for Terminal [C1]
(Bias value)
-100.00 to 100.00%
Y Y 0.00
C62 (Bias base point) 0.00 to 100.00% Y Y 0.00
C64 (Display unit) Same as C58. Y Y 2
C65 (Maximum scale) -999.00 to 0.00 to 9990.00
N Y 100
C66 (Minimum scale) -999.00 to 0.00 to 9990.00
N Y 0.00
C67 Analog Input Adjustment for Terminal [V2]
(Bias value)
-100.00 to 100.00% Y Y 0.00
C68 (Bias base point) 0.00 to 100.00%
Y Y 0.00
C70 (Display unit) Same as C58. Y Y 2
C71 (Maximum scale) -999.00 to 0.00 to 9990.00
N Y 100
C72 (Minimum scale) -999.00 to 0.00 to 9990.00
N Y 0.00
Note: Alphabets in the Default setting field denote shipping destination: E (EU), A (Asia), C (China).
P codes: Motor 1 Parameters
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
P01 Motor 1 (No. of poles) 2 to 22 poles
N Y1 4
P02 (Rated capacity) 0.01 to 1000.00 kW (when P99 = 0 or 4)
0.01 to 1000.00 HP (when P99 = 1)
N Y1 *6
P03 (Rated current) 0.00 to 2000.00 A
N Y1 *6
P04 (Auto-tuning) 0: Disable
1: Tune the motor while it is stopped (%R1, %X)
2: Tune the motor while it is rotating under V/f control
(%R1, %X, no-load current)
N N 0
P05 (Online-tuning) 0: Disable
1: Enable
Y Y 0
P06 (No-load current) 0.00 to 2000.00 A
N Y1 *6
P07 (%R1) 0.00% to 50.00%
Y Y1 *6
P08 (%X) 0.00% to 50.00% Y Y1 *6
P10 (Slip compensation response time) 0.01 to 10.00 s Y Y1 0.50
P12 (Rated slip frequency) 0.00 to 15.00 Hz
N Y1 *6
P99 Motor 1 Selection 0: Motor characteristics 0 (Fuji standard motors, 8-series)
1: Motor characteristics 1 (HP rating motors)
4: Other motors
N Y1 0
The shaded function codes ( ) are applicable to the quick setup.
*6 The motor parameters are automatically set, depending upon the inverter's capacity. See Table B.