Fuji Electric FRENIC-AQUA series, User Manual

Page: 310 / 751

6.2 Function Code Tables
6-29
Chap. 6
FUNCTION C
ODES
U codes: Customizable Logic Function
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
U00 Customizable Logic (Mode selection) 0: Disable
1: Enable (Customizable logic operation)
Changing this code data from "1" to "0" causes an ECL alarm.
Y Y 0
U01 Customizable Logic: Step 1
(Control function)
0: No function assigned
10: Through General-purpose timer
20: General-purpose timer
30: ORing + General-purpose timer
40: General-purpose timer
50: Set priority flip-flop + General-purpose timer
60: Reset priority flip-flop + General-purpose timer
70: Rising edge de General-purpose timer
80: Falling edge de General-purpose timer
90: Rising & falling edges de General-purpose timer
100: Hold + General-purpose timer
110: Increment counter
120: Decrement counter
130: Timer with reset input
2001-3002: Analog input
4001-5114: digital
N Y 0
U02 (Input 1) 0 (1000): Inverter running ( RUN )
N Y 100
U03 1 (1001): Frequency (speed) arrival signal ( FAR )
2 (1002): Frequency (speed) detected ( FDT )
3 (1003): Undervoltage detected (Inverter stopped) ( LV )
5 (1005): Inverter output limiting ( IOL )
6 (1006): Auto-restarting after momentary power
failure ( IPF )
7 (1007): Motor overload early warning ( OL )
10 (1010): Inverter ready to run ( RDY )
11: Switch motor drive source between
commercial power and inverter output
(For MC on commercial line)
( SW88 )
12: Switch motor drive source between
commercial power and inverter output
(For secondary side)
( SW52-2 )
13: Switch motor drive source between
commercial power and inverter output
(For primary side)
( SW52-1 )
15 (1015): Select AX terminal function
(For MC on primary side) ( AX )
16 (1016): Shifted to pattern operation stage ( TU )
17 (1017): Pattern operation cycle completed ( TO )
18 (1018): Pattern operation stage number ( STG1 )
19 (1019): Pattern operation stage number ( STG2 )
20 (1020): Pattern operation stage number ( STG4 )
22 (1022): Inverter output limiting with delay ( IOL2 )
25 (1025): Cooling fan in operation ( FAN )
26 (1026): Auto-resetting ( TRY )
27 (1027): Universal DO ( U-DO )
28 (1028): Heat sink overheat early warning ( OH )
30 (1030): Lifetime alarm ( LIFE )
33 (1033): Reference loss detected ( REF OFF )
35 (1035): Inverter output on ( RUN2 )
36 (1036): Overload prevention control ( OLP )
37 (1037): Current detected ( ID )
42 (1042): PID alarm ( PID-ALM )
43 (1043): Under PID control ( PID-CTL )
44 (1044): Motor stopped due to slow
flowrate under PID control ( PID-STP )
45 (1045): Low output torque detected ( U-TL )
52 (1052): Running forward ( FRUN )
53 (1053): Running reverse ( RRUN )
54 (1054): In remote operation ( RMT )
55 (1055): Run command entered ( AX2 )
56 (1056): Motor overheat detected by thermistor ( THM )
59 (1059): Terminal [C1] wire break ( C1OFF )
68 (1068): Motor regular switching early warning ( MCHG )
69 (1069): Pump control output limit signal ( MLIM )