Fuji Electric FRENIC-AQUA series, User Manual

Page: 304 / 751

6.2 Function Code Tables
6-23
Chap. 6
FUNCTION C
ODES
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
J459 Motor Decrease Switching Level 0 to 100%, Inherit
Inherit: Depends on J456 Y Y Inherit
J460 Motor Decrease PID Control Start
Frequency
0 to 120 Hz, Inherit
Inherit: Depends on J450 Y Y Inherit
J461 Motor Increase/Decrease Switching
Judgment Non-responsive Area Width
OFF, 0.1 to 50.0%
OFF: Disable
0.1 to 50.0% Y Y OFF
J462 Failure Inverter Judgment Time OFF, 0.5 to 600.0 s
Y Y 5.0
J465 Auxiliary Motor
(Frequency operation level)
0.1 to 120.0 Hz
OFF: Disable Y Y 50.0
J466 (Hysteresis width) 0.0 to 120.0 Hz
Y Y 1.0
J467 (PV operation level) 0.01 to 9990.00 *10
OFF: Disable
Y Y OFF
J468 (Connection timer) 0.00 to 2.00 s
Y Y 0.00
J469 (Interrupting timer) 0.00 to 2.00 s
Y Y 0.00
J480 Motor Cumulative Run Time (Motor 0) Y N 0
J481 (Motor 1)
0 to 65535
For adjustment at the replacement time
J482 (Motor 2)
J483 (Motor 3)
J484 (Motor 4)
J485 (Motor 5)
J486 (Motor 6)
J487 (Motor 7)
J488 (Motor 8)
J490 Y Terminal ON Maximum Cumulation Count
(Y1 Y2)
J491 (Y3 Y4)
J492 Relay ON Maximum Cumulation Count
(Y5A 30AB)
J493 (Y6RY to Y12RY)
0.000 to 9999
(The display of "1.000" indicates 1000 times.) Y N 0.000
J5 codes: External PID Function 1
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
J501 External PID Control 1 (Mode selection) 0 Disable
1: Enable process control (Normal operation)
2: Enable process control (Inverse operation)
11: Enable process control, interlocking with inverter running
(Normal operation)
12: Enable process control, interlocking with inverter running
(Inverse operation)
21: Enable process control by external digital signal (Normal
operation)
22: Enable process control by external digital signal (Inverse
operation)
31: Enable process control by external digital signal, interlocking
with inverter running (Normal operation)
32: Enable process control by external digital signal, interlocking
with inverter running (Inverse operation)
N Y 0
J502 (Remote command selection) 0: Keypad ( / key)
3: UP / DOWN
4: Command via communications link (Use function code S13)
51: External PID command 1 (Analog input: Terminals [12], [C1]
and [V2])
N Y 0
J503 (Feedback selection) 51: External PID feedback value 1
60: Addition (External PID feedback value 1 + External PID
feedback value 2)
61: Difference External PID feedback value 1 - External PID
feedback value 2)
62: Average (External PID feedback value 1, External PID
feedback value 2)
63: Maximum (External PID feedback value 1, External PID
feedback value 2)
64: Minimum (External PID feedback value 1, External PID
feedback value 2)
N Y 51
*10 The upper and lower level values are restricted by the maximum and minimum scales.