Fuji Electric FRENIC-AQUA series, User Manual

Page: 287 / 751

6-6
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
190 (1190): Cancel timer ( TMC )
191 (1191): Enable timer 1 ( TM1 )
192 (1192): Enable timer 2 ( TM2 )
193 (1193): Enable timer 3 ( TM3 )
194 (1194): Enable timer 4 ( TM4 )
201 (1201): External PID control 1 ON command ( EPID1-ON )
202 (1202): Cancel external PID control 1 ( %/EPID1 )
203 (1203): Switch normal/inverse operation
under external PID control 1 ( EPID1-IVS )
204 (1204): Reset external PID1 integral and
differential components ( EPID1-RST )
205 (1205): Hold external PID1 integral component
( EPID1-HLD )
211 (1211): External PID control 2 ON command ( EPID2-ON )
212 (1212): Cancel external PID control 2 ( %/EPID2 )
213 (1213): Switch normal/inverse operation
under external PID control 2 ( EPID2-IVS )
214 (1214): Reset external PID2 integral and
differential components ( EPID2-RST )
215 (1215): Hold external PID2 integral component
( EPID2-HLD )
221 (1221): External PID control 3 ON command ( EPID3-ON )
222 (1222): Cancel external PID control 3 ( %/EPID3 )
223 (1223): Switch normal/inverse operation
under external PID control 3 ( EPID3-IVS )
224 (1224): Reset external PID3 integral and
differential components ( EPID3-RST )
225 (1225): Hold external PID3 integral component
( EPID3-HLD )
Setting the value in parentheses ( ) shown above assigns a
negative logic output to a terminal. (True if OFF.)
Setting the value of 1000s in parentheses ( ) shown above
assigns a negative logic input to a terminal.
E10 Acceleration Time 2
Y Y 20.00
E11 Deceleration Time 2 Y Y 20.00
E12 Acceleration Time 3 Y Y 20.00
E13 Deceleration Time 3
Y Y 20.00
E14 Acceleration Time 4
Y Y 20.00
E15 Deceleration Time 4
0.00 to 3600.00 s
Note: Entering 0.00 cancels the acceleration time, requiring
external soft-start and -stop.
Y Y 20.00
E16 Torque Limiter 2 (Driving) Y Y OFF
E17 (Braking)
OFF: Disable
20% to 150%: Torque limiter level
Y Y OFF
E20 Terminal [Y1] Function N Y 0
E21 Terminal [Y2] Function N Y 1
E22 Terminal [Y3] Function
N Y 2
E23 Terminal [Y4] Function
N Y 7
E24 Terminal [Y5A/C] Function N Y 15
E27 Terminal [30A/B/C] Function
(Relay output)
Selecting function code data assigns the corresponding function
to terminals [Y1] to [Y5A/C] and [30A/B/C] as listed below.
0 (1000):
Inverter running ( RUN )
1 (1001): Frequency (speed) arrival signal ( FAR )
2 (1002): Frequency (speed) detected ( FDT )
3 (1003): Undervoltage detected (Inverter stopped) ( LV )
5 (1005): Inverter output limiting ( IOL )
6 (1006): Auto-restarting after momentary power
failure ( IPF )
7 (1007): Motor overload early warning ( OL )
10 (1010): Inverter ready to run ( RDY )
11: Switch motor drive source between
commercial power and inverter output
(For MC on commercial line) ( SW88 )
12: Switch motor drive source between
commercial power and inverter output
(For secondary side) ( SW52-2 )
13: Switch motor drive source between
commercial power and inverter output
(For primary side) ( SW52-1 )
15 (1015): Select AX terminal function
(For MC on primary side) ( AX )
16 (1016): Shifted to pattern operation stage ( TU )
17 (1017): Pattern operation cycle completed ( TO )
18 (1018): Pattern operation stage number ( STG1 )
19 (1019): Pattern operation stage number ( STG2 )
20 (1020): Pattern operation stage number ( STG4 )
22 (1022): Inverter output limiting with delay ( IOL2 )
25 (1025): Cooling fan in operation ( FAN )
26 (1026): Auto-resetting ( TRY )
27 (1027): Universal DO ( U-DO )
28 (1028): Heat sink overheat early warning ( OH )
30 (1030): Lifetime alarm ( LIFE )
31 (1031): Frequency (speed) detected 2 ( FDT2 )
33 (1033): Reference loss detected ( REF OFF )
35 (1035): Inverter output on ( RUN2 )
36 (1036): Overload prevention control ( OLP )
37 (1037): Current detected ( ID )
42 (1042): PID alarm ( PID-ALM )
43 (1043): Under PID control ( PID-CTL )
N Y 99