Fuji Electric FRENIC-AQUA series, User Manual

Page: 284 / 751

6.2 Function Code Tables
6-3
Chap. 6
FUNCTION C
ODES
The following tables list the function codes available for the FRENIC-AQUA series of inverters.
F codes: Fundamental Functions
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
F00 Data Protection 0: Disable both data protection and digital reference protection
1: Enable data protection and disable digital reference protection
2: Disable data protection and enable digital reference protection
3: Enable both data protection and digital reference protection
Y Y 0
F01 Frequency Command 1 0: / / / keys on keypad
1: Voltage input to terminal [12] (-10 to +10 VDC)
2: Current input to terminal [C1] (4 to 20 mA DC)
3: Sum of voltage and current inputs to terminals [12] and [C1]
5: Voltage input to terminal [V2] (0 to 10 VDC)
7: Terminal command
UP/DOWN control
8: / / / keys on keypad
(balanceless-bumpless switching available)
10: Pattern operation
N Y 0
F02 Operation Method 0: FWD/REV/STOP keys on keypad (Motor rotational direction
specified by terminal command FWD / REV )
1: External signals (Terminal command FWD or REV )
2: FWD/STOP keys on keypad (forward)
3: REV/STOP keys on keypad (reverse)
N Y 0
F03 Maximum Frequency 1 25.0 to 120.0 Hz
N Y 50.0
F04 Base Frequency 1 25.0 to 120.0 Hz
N Y 50.0
F05 Rated Voltage at Base Frequency 1 0: Output a voltage in proportion to input voltage
160 to 500 V: Output an AVR-controlled voltage
N Y
F06 Maximum Output Voltage 1 160 to 500 V: Output an AVR-controlled voltage
N Y
E: 400
A: 415
C: 380
F07 Acceleration Time 1
Y Y 20.00
F08 Deceleration Time 1
0.00 to 3600.00 s
Note: Entering 0.00 cancels the acceleration time, requiring
external soft-start.
Y Y 20.00
F09 Torque Boost 1 0.0% to 20.0% (percentage with respect to "F05: Rated Voltage at
Base Frequency 1")
Y Y *1
F10 Electronic Thermal Overload Protection for
Motor 1
(Select motor characteristics)
1: For a general-purpose motor with shaft-driven cooling fan
2: For an inverter-driven motor, non-ventilated motor, or motor
with separately powered cooling fan
Y Y 1
F11 (Overload detection level) OFF: Disable
1% to 135% of the inverter rated current
Y Y1 *3
F12 (Thermal time constant) 0.5 to 75.0 min
Y Y *2
F14 Restart Mode after Momentary Power
Failure (Mode selection)
0: Trip immediately
1: Trip after a recovery from power failure
3: Continue to run, for heavy inertia or general loads
4: Restart at the frequency at which the power failure occurred,
for general loads
5: Restart at the starting frequency
Y Y E: 0
A/C: 1
F15 Frequency Limiter (High) 0.0 to 120.0 Hz Y Y 70.0
F16 (Low) 0.0 to 120.0 Hz
Y Y 0.0
F18 Bias (Frequency command 1) -100.00% to 100.00%
Y* Y 0.00
F20 DC Braking 1
(Braking starting frequency)
0.0 to 60.0 Hz Y Y 0.0
F21 (Braking level) 0% to 60%
on the basis of inverter rated current
Y Y 0
F22 (Braking time) OFF (Disable); 0.01 to 30.00 s
Y Y OFF
F23 Starting Frequency 1 0.1 to 60.0 Hz
Y Y 0.5
F24 (Holding time) 0.00 to 10.00 s Y Y 0.00
F25 Stop Frequency 0.1 to 60.0 Hz Y Y 0.2
F26 Motor Sound (Carrier frequency) 0.75 to 16 kHz (0.75 to 37 kW)
0.75 to 10 kHz (45 to 90 kW)
0.75 to 6 kHz (110 to 630 kW)
0.75 to 4 kHz (710 kW)
Y Y 2
F27 (Tone) 0: Level 0 (Inactive)
1: Level 1
2: Level 2
3: Level 3
Y Y 0
F29 Analog Output [FM1] (Mode selection) 0: Output in voltage (0 to 10 VDC)
1: Output in current (4 to 20 mA DC)
2: Output in current (0 to 20 mA DC)
Y Y 0
F30 (Voltage adjustment) 0% to 300% Y* Y 100
The shaded function codes ( ) are applicable to the quick setup.
Note: Alphabets in the Default setting field denote shipping destination: E (EU), A (Asia), C (China).
*1 The factory default differs depending upon the inverter's capacity. See Table A.
*2 5.0 min for inverters with a capacity of 22 kW or below; 10.0 min for those with 30 kW or above
*3 The motor rated current is automatically set. See Table B (function code P03).