System Manual – MOVIDRIVE® compact Drive Inverters
297
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Wiring diagram for basic unit
Installation
MCF/MCV/MCS4_A control unit: Circuit diagram for the control unit
•
MCF/MCV/MCS41A (with PROFIBUS-DP): SEW-EURODRIVE recommends that
you always supply these units with DC 24 V at terminal X10:24 (VI24). This external
DC 24 V voltage supply must be able to provide 50 W continuous power and 100 W
peak power (1-s).
•
Analog input AI21 (X10:6) can be used either as a 10 V voltage input or as a TF/TH
input. It is switched over using parameter P120.
•
You can only access DIP switches S11, S12 and 1 ... 10 when the connection unit is
removed (
→
Sec. "Removing the connection unit").
•
The functions of the DIP switches 1 ... 10 are explained in the sections "Bus termi-
nation" and "Setting the station address."
•
The TF/TH line must either be shielded or routed at a distance of at least 0.2 m from
power cables (e.g. motor or brake cables). The TF/TH line must be shielded sepa-
rately if hybrid cables are used for the motor and TF/TH connection.
59873AEN
Control unit
X10:
Optional
keypad
Optional
serial
interface
Incremental
encoder output
simulation or
external encoder
input
Input
motor encoder
PROFIBUS-DP
connection
X30:
Only in
MCF/MCV/MCS41A
X15:
Only in
MCV/MCS
X14:
Only in
MCV/MCS
Shield
terminal
Settings
PROFIBUS-DP only in
MCF/MCV/MCS41A
ON OFF
ON OFF*
AGND (reference potential
DC 10 V analog signals)
DGND (reference potential
DC 24 V analog signals)
Protective earth (shield)
* Factory setting
** If the binary inputs are switched
with DC 24 V by VO24, then
DCOM must be jumpered with
DGND !
DC 24 V
K12
(AC-3)
1
2
3
4
5
6
7
8
9
10
S12
S11
Reference for
binary outputs
Binary
outputs
Binary input
Higher-level
controller
R11
-10 V...+10 V
0(4)...20 mA
DC+24 V input
Reference potential for binary signals
NC relay
NOC relay
/Brake
No
function*
Ready*
Relay contact
Referene potential for binary signals
DC+24 V output
Reference X10:DIØØ...DIØ5
n12/n22*
n11/n21*
Enable/stop*
CW/stop*
CCW/stop*
/Controller inhibit
Reference potential for analog signals
System bus low
n2 (0...10 V)/ TF/TH input*
System bus high
4...20 mA
0...20 mA
+/-10 V
n1
0...10 V
+10 V
-10 V
U
REF1
AI11***
REF2
AI12***
SC11
AI21
SC12
AGND
DIØØ
DIØ1
DIØ2
DIØ3
DIØ4
DIØ5
DCOM**
VO24
DGND
DOØ1-C
DOØ2/AO1
DOØ1/NO
DBØØ
DOØ1/NC
DGND
VI24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
*** AI11/AI12 are not evaluated in
MCF41A !
Summary of Contents for MOVIDRIVE compact MCH41A
Page 2: ...SEW EURODRIVE Driving the world...
Page 432: ......
