manualshive.com logo in svg

Schweitzer Engineering Laboratories SEL-421-4, Instruction Manual

Share
Download
Schweitzer Engineering Laboratories SEL-421-4 Instruction Manual Download Page 429

6.93

Date Code 20171021

Instruction Manual

SEL-421  Relay

Protection Applications Examples

EHV Parallel 230 kV Underground Cables Example

Occasional loss-of-potential to the distance relay, while unavoidable, is detect-
able. When the relay detects a loss-of-potential condition, the relay can block dis-
tance element operation, block or enable forward-looking directional overcurrent 
elements, and issue an alarm for any true loss-of-potential condition.

If line-side PTs are used, the circuit breaker(s) must be closed for the LOP logic 
to detect a loss-of-potential condition. Therefore, if three-phase potential to the 
relay is lost while the circuit breaker(s) is open (e.g., the PT fuses are removed 
while the line is de-energized), the relay cannot detect a loss-of-potential condi-
tion when the circuit breaker(s) closes again. At circuit breaker closing, the relay 
can detect one or two missing potentials that occurred while the circuit breaker 
was open. See 

Loss-of-Potential Logic on page 5.28

 for more information.

Table 6.24

 lists the three choices for enabling LOP protection.

                    

Set ELOP to Y1 for this application example. This choice reduces the chances of 
false tripping because of a loss-of-potential condition.

ELOP := 

Y1

.

Loss-of-Potential (Y, Y1, N)

Enable the Advanced Settings so you can properly set the zero-sequence com-
pensation factors.

EADVS := 

Y

.

Advanced Settings (Y, N)

Phase-Distance Elements (21P)

Mho Phase-Distance Element Reach

Employ each zone of distance protection as follows:

➤

Zone 1—Instantaneous underreaching tripping

➤

Zone 2—Forward-looking fault detector for the POTT scheme and 
backup time delayed tripping

➤

Zone 3—Current reversal guard for the POTT scheme, echo tripping, 
and weak infeed logic

Zone 1 Phase-Distance Element Reach

Zone 1 phase-distance protection provides instantaneous protection for phase-to-
phase, phase-to-phase-to-ground, and three-phase faults in the first 80 percent of 
the cable. Errors in the current transformers, potential transformers, modeled 
cable data, and fault study data do not permit a Zone 1 setting for 100 percent of 
the cable; unwanted tripping could occur for faults just beyond the remote end of 
the cable.

Table 6.24

LOP Enable Options

Option

Description

N

The LOP logic operates but does not disable voltage-polarized directional ele-
ments, distance elements, and forward-looking directional overcurrent ele-
ments. Use LOP in this case for alarm only.

Y

The relay disables all voltage-polarized directional elements and distance ele-
ments, but enables forward-looking directional overcurrent elements. These 
forward-looking directional overcurrent elements effectively become nondirec-
tional and provide overcurrent protection during a loss-of-potential condition.

Y1

The relay disables all voltage-polarized directional elements and distance ele-
ments. The relay also disables the overcurrent elements controlled by the volt-
age-polarized directional elements.

Summary of Contents for SEL-421-4















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands