manualshive.com logo in svg

Schweitzer Engineering Laboratories SEL-421-4, Instruction Manual

Share
Download
Schweitzer Engineering Laboratories SEL-421-4 Instruction Manual Download Page 1326

16.10

SEL-400 Series Relays

Instruction Manual

Date Code 20171006

DNP3 Communication

DNP3 in the Relay

Binary Controls

The relay provides more than one way to control individual points within the 
relay. The relay maps incoming control points either to remote bits within the 
relay or to internal command bits that cause circuit breaker operations.

NOTE: 

The port setting DNPCL (or 

DNPCL

n

 for DNP3 LAN/WAN session 

n) must be set to Y to enable binary 
controls for the DNP3 session. Binary 
Output Status requests (Object 10, 
Variation 2) and Class 0 requests will 
have no Binary Outputs in the 
response unless DNPCL := Y.

A DNP3 technical bulletin (

Control Relay Output Block Minimum Implementa-

tion 9701-002

) recommends that you use one point per Object 12, control block 

output relay. You can use this method to perform pulse on, latch on, and latch off 
operations on selected remote bits.

If your master does not support the single-point-per-index messages or single-
operation database points, you can use the trip/close operation or use the code 
field in the DNP3 message to specify operation of the points shown in 

Control 

Point Operation on page 16.20

.

Time Synchronization

The accuracy of DNP3 time synchronization is insufficient for most protection 
and oscillography needs. DNP3 time synchronization provides backup time syn-
chronization in the event the relay loses primary synchronization through the 
IRIG-B TIME input or some other high accuracy source. 

Enable time synchronization with the TIMERQ setting (TIMERQ

n

 for DNP3 

LAN/WAN Session 

n

) and use Object 50, Variation 1, and Object 52, Variation 2 

(Object 50, Variation 3 for DNP3 LAN/WAN), to set the time via a DNP3 master.

TIMERQ can be set in one of three ways:

➤

A numeric setting of 1–32767 minutes specifies the rate at which the 
relay shall request a time synchronization.

➤

A setting of M disables the relay from requesting a time 
synchronization, but still allows the relay to accept and apply time 
synchronization messages from the master.

➤

A setting of I disables the relay from requesting a time 
synchronization, and sets the relay to ignore time synchronization 
messages from the master.

Effective January 1, 2008, the DNP3 standard requires that DNP3 time corre-
spond to Coordinated Universal Time (UTC). To help ease into the transition to 
this standard, you can use the DNPSRC Global setting to determine whether the 
relay will use local or UTC time for DNP3.

When requesting time synchronization with DNPSRC := UTC, the relay will 
treat incoming DNP3 time set messages as UTC time. All DNP3 event time-
stamps (binary input changes with time, analog input changes with time, etc.) 
will be in UTC time.

When requesting time synchronization with DNPSRC := LOCAL, the relay will 
treat incoming time set by the DNP3 master as local time. All DNP3 event time-
stamps will be in local time.

When setting the time with local time, there is an ambiguity during the last hour 
of daylight-saving time (DST) and to resolve this ambiguity, if the relay accepts a 
Time Set request in this hour, it will assume the time is in DST.

Summary of Contents for SEL-421-4















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands