Rohde & Schwarz NRP2 User Manual Download Page 338

Page: 338 / 419

Remote Control - Commands

NRP2

335

User Manual 1173.9140.02 ─ 07

Parameters:

<state>

BUS | EXTernal | HOLD | IMMediate | INTernal

BUS

The trigger event is initiated by

TRIG:IMM

*TRG

. In this case,

the other trigger setting are meaningless.

EXTernal

Triggering is performed with an external signal applied to the
trigger connector. The

TRIG:SLOP

command determines

whether the rising or the falling edge of the signal is to be used
for triggering. Waiting for a trigger event can be skipped by

TRIG:IMM

HOLD

A measurement can only be triggered when the command

TRIG:IMM

is executed.

IMMediate

The sensor does not remain in the WAIT_FOR_TRG state but
immediately changes to the MEASURING state.

INTernal

The sensor determines the trigger time by means of the signal to
be measured. When this signal exceeds (

TRIG:SLOP POS

) or

fall short of (

TRIG:SLOP NEG

) the power set by

TRIG:LEV

, the

measurement is started after the time set by

TRIG:DEL

. Similar

TRIG:SOUR EXT

, waiting for a trigger event can also be skip-

ped by

TRIG:IMM

*RST:

depending on sensor

TRIGger<[1]..4>:SYNChronize[:STATe]

<state>

If set to

, the command blocks the external trigger bus as long as the sensor is not in

WAIT_FOR_TRIGGER state. It is usually used in combination with command

TRIG:MAST

and makes certain, that a new measurement will only be started after all

sensors have completed their last measurement.

Parameters:

<state>

ON | OFF
*RST:

depending on sensor

6.16 UNIT

Commands of the UNIT system

UNIT<[1]..8>:POWer

...................................................................................................... 336

UNIT<[1]..8>:POWer:RATio

............................................................................................ 336

UNIT

北京海洋兴业科技股份有限公司（证券代码：839145）

电话：010-62176775

网址：www.hyxyyq.com

Summary of Contents for NRP2




































































































































































































































































































































































































































Search results

Summary of Contents for NRP2

Reviews:

Brands by name

Popular brands

Rohde & Schwarz NRP2, User Manual

Search results

Summary of Contents for NRP2

Reviews:

Brands by name

Popular brands