Rohde & Schwarz CMU-K20, Operating Manual

Page: 420 / 646

Common: SPECtrum:SWITching CMU-K20/21/22/23/24
1115.6088.12 6.116 E-12
Default values for GSM1800 (both modulation schemes):
Level <nr> Level / [dBm] 0.4 MHz / [dBc] 0.6 MHz / [dBc] 1.2 MHz / [dBc] 1.8 MHz / [dBc]
1
≥
36.0 –16.0 –21.0 –21.0 –24.0
2 34.0 –18.0 –21.0 –21.0 –24.0
3 32.0 –20.0 –22.0 –22.0 –25.0
4 30.0 –22.0 –24.0 –24.0 –27.0
5 28.0 –23.0 –25.0 –26.0 –29.0
6 26.0 –23.0 –26.0 –28.0 –31.0
7 24.0 –23.0 –26.0 –30.0 –33.0
8 22.0 –23.0 –26.0 –31.0 –35.0
9
≤
20.0 –23.0 –26.0 –32.0 –36.0
Default values for GSM1900 (both modulation schemes):
Level <nr> Level / [dBm] 0.4 MHz / [dBc] 0.6 MHz / [dBc] 1.2 MHz / [dBc] 1.8 MHz / [dBc]
1
≥
33.0 –19.0 –22.0 –22.0 –25.0
2 32.0 –20.0 –22.0 –22.0 –25.0
3 30.0 –22.0 –24.0 –24.0 –27.0
4 28.0 –23.0 –25.0 –26.0 –29.0
5 26.0 –23.0 –26.0 –28.0 –31.0
6 24.0 –23.0 –26.0 –30.0 –33.0
7 22.0 –23.0 –26.0 –31.0 –35.0
8
≤
20.0 –23.0 –26.0 –32.0 –36.0
CONFigure:SPECtrum:SWITching[:GMSK]:LIMit:LINE:MODE[:UPPer] <Mode>
CONFigure:SPECtrum:SWITching:EPSK:LIMit:LINE:MODE[:UPPer] <Mode> Limit Check on/off
<Mode> Description of parameters Def. value Def. unit FW vers.
ON |
OFF Switch on limit lines
Switch off limit lines ON – V1.20
Description of command
This command switches all limits for the spectrum due to switching measurement on or off.
CONFigure:SPECtrum:SWITching[:GMSK]:LIMit:LINE:DEFault <Enable>
CONFigure:SPECtrum:SWITching:EPSK:LIMit:LINE:DEFault <Enable> Default Settings
<Enable> Description of parameters Def. value Def. unit FW vers.
ON |
OFF All the parameters of the subsystem are set to default val-
ues
At least one parameter of the subsystem differs from its de-
fault value ON
– V2.00
Description of command
If used as a setting command with ON , this command sets all the parameters of the subsystem to their default
values ( OFF causes an error message). In the query format, the command returns ON if all the parameters of the
subsystem correspond to their default values, otherwise it returns OFF .
深圳德标仪器
135-1095-0799