Rohde & Schwarz CMU-K20, Operating Manual

Page: 318 / 646

Measurement Groups (Non Signalling only) CMU-K20/K21/K22/K23/K24
1115.6088.12 6.14 E-12
CONFigure:POWer[:NORMal]:EPSK:CONTrol:RPMode <Mode> Ref. Power Mode
<Mode> Description of parameters Def. value Def. unit FW vers.
CURRent |
AVERage |
DCOMpens Ref. Power calculated from current burst
Ref. Power calculated from average curve
Data compensated/corrected reference power CURR – V2.15
Description of command
This command determines how the reference power (0-dB line in the P/t Norm. 8PSK test diagram) for 8PSK-
modulated signals is calculated.
CONFigure:POWer[:NORMal][:GMSK]:CONTrol:DEFault <Enable> Default Settings
CONFigure:POWer[:NORMal]:EPSK:CONTrol:DEFault <Enable>
<Enable> Description of parameters Def. value Def. unit FW vers.
ON |
OFF The parameters are set to their default values
Some or all parameters differ from the default values ON
– V2.00
Description of command
If used as a setting command with the parameter ON this command sets all parameters of the subsystem to their
default values (the setting OFF causes an error message).
If used as a query the command returns whether all parameters are set to their default values (ON) or not (OFF) .
Subsystem POWer:LIMit:LINE
The subsystem POWer:LIMit:LINE defines the limit lines, i.e. the tolerance values for the power meas-
urement. The subsystem corresponds to the tab Limit Lines in the popup menu Power Configuration.
CONFigure:POWer[:NORMal][:GMSK]:LIMit:LINE:UPPer<nr>[:STATic]:ENABle <Enable>
CONFigure:POWer[:NORMal]:EPSK:LIMit:LINE:UPPer<nr>[:STATic]:ENABle <Enable>
CONFigure:POWer[:NORMal][:GMSK]:LIMit:LINE:UPPer<nr>[:STATic]
CONFigure:POWer[:NORMal]:EPSK:LIMit:LINE:UPPer<nr>[:STATic]
Upper Limit Line
Parameters for query: <StartTime>, <EndTime>, <StartRelLevel>, <EndRelLevel>,
<StartAbsLevel>, <EndAbsLevel>, <StartVisibility>, <EndVisibility>
for setting: <StartTime>, <EndTime>, <StartRelLevel>, <EndRelLevel>,
<StartAbsLevel>, <EndAbsLevel>, <Visibility>
Parameters Value range Description of parameters Def. values
<Enable>
<StartTime>,
<EndTime>,
<StartRelLevel>,
<EndRelLevel>,
<StartAbsLevel>,
<EndAbsLevel>,
<Visibility>
<StartVisib>
<EndVisib> ON | OFF
–10 bit to +156 ¾ bit | OFF
–10 bit to +156 ¾ bit | OFF,
–100 dB to 20 dB | OFF,
–100 dB to 20 dB | OFF,
–90 dBm to 50.0 dBm OFF,
–90 dBm to 50.0 dBm | OFF,
ON | OFF Area on/off
Start point of time
End point of time
Start point of level (relative)
End point of level (relative)
Start point of level (absolute)
End point of level (absolute)
Range of limit lines on/off
see below
Description of command FW vers.
These commands activate and define upper limit lines for normal bursts. The limit lines are defined
area by area; the suffix <nr> numbers the various areas in the burst diagram (see chapter 4).
V1.15
深圳德标仪器
135-1095-0799