manualshive.com logo in svg

Nautilus Hyosung MX8800, Manual, Page: 488 / 827

Share
Download
Nautilus Hyosung MX8800 Manual Download Page 488

 

Error Code Manual                                                                                                    Chapter2. Bill Recycling Machine (BRM) 

 

2-484                                     

©  2014 

Nautilus Hyosung Inc. 

All Rights Reserved.

 

 

Code 

Problem Description 

Troubleshooting 

5KA2W00 

Status of remaining notes on 
the during Transport Path 
(GS802) before the operation 
during Withdrawal Reject. 

1. Open the upper unit 
2. Open the customer service module 
(CSM) 
3. Open the BC(5) 
4. Remove notes and substance in the 
BC(5) 
5. Check whether the sensor is 
contaminated or not if there are No 
notes or substance 

5KAA100 

Status of UTC removal before 
Run during Withdrawal Reject. 

1. Open the upper unit 
2. Check removal of the cassette not 
received(9) 

5KAA200 

Status of TE open before the 
operation during Withdrawal 
Reject. 

1. Open the upper Unit 
2. Check open/close of TE(12) 

5KAA300 

Status of BMU inter lock 
detachment before the 
operation during Withdrawal 
Reject. 

1. Check Load/Removal of the upper 
unit 
2. Replace a cherry switch when error 
occures 

5KAA400 

Status of BMU detachment 
before the operation during 
Withdrawal Reject. 

1. Check Load/Removal of the upper 
unit 

5KAA600 

Status of CSM open before the 
operation during Withdrawal 
Reject. 

1. Open the upper Unit 
2. Check open/close of CSM 
3. Check sensor GS011 

5KAA700 

Status of RJC detachment 
before the operation during 
Withdrawal Reject. 

1. Open the lower unit 
2. Open the Mid Transport Path 
3. Check the reject CST(21) 
Load/Removal 

5KAA800 

Status of BMD inter lock before 
the operation during 
Withdrawal Reject. 

1. Check the lower Unit load/removal 
2. Check the lower unit status of inter 
lock 
3. Exchange the cherry switch or clean 
the inter lock sensor(or exchange) if 
occur same error 

5KAA900 

Status of BMD detachment 
before the operation during 
Withdrawal Reject. 

1. Check the lower Unit load/removal 
2. Check the lower unit status of inter 
lock 
3. Exchange the cherry switch or clean 
the inter lock sensor(or exchange) if 
occur same error 

5KAAA00 

Status of BC open before the 
operation during Withdrawal 
Reject. 

1. Open the upper unit 
2. Check the lock lever in the BC 

5KAAC00 

Status of RJC full before the 
operation during Withdrawal 
Reject. 

1. Open the lower unit 
2. Open the Mid Transport Path 
3. Remove reject cassette(21) 
4. Remove notes after checking notes 
full in the cassette 
5. Check whether the sensor is 
contaminated or not if a cassette is 
empty. 

5KAAL00 

Abnormal status of 
RC(Removal, Not Used, 
Withdrawal RC) to stack during 
Withdrawal Reject. 

1. Open the lower unit 
2. Check status of RC (Note Used, 
Failure Status) 
3.Operate to initialize BRM(Recovery) 

Summary of Contents for MX8800




























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments