manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 370

 

10-2

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

Signaling Events and Alarms

This section provides a brief overview of the signaling events and alarms for the BTS 10200 in numerical 
order. 

Table 10-1

 lists all of the signaling events and alarms by severity.

Note

Click the signaling message number in 

Table 10-1

 to display information about the event or alarm.

Table 10-1

Signaling Events and Alarms by Severity 

CRITICAL

MAJOR

MINOR

WARNING

INFO

NOT USED

SIGNALING (12)

SIGNALING (7)

SIGNALING (10)

SIGNALING (4)

SIGNALING (1)

SIGNALING (2)

SIGNALING (64)

SIGNALING (8)

SIGNALING (14)

SIGNALING (6)

SIGNALING (42)

SIGNALING (3)

SIGNALING (65)

SIGNALING (9)

SIGNALING (15)

SIGNALING (25)

SIGNALING (43)

SIGNALING (5)

SIGNALING (69)

SIGNALING (11)

SIGNALING (16)

SIGNALING (26)

SIGNALING (44)

SIGNALING (35)

SIGNALING (75)

SIGNALING (13)

SIGNALING (17)

SIGNALING (27)

SIGNALING (45)

SIGNALING (37)

SIGNALING (80)

SIGNALING (19)

SIGNALING (18)

SIGNALING (28)

SIGNALING (46)

SIGNALING (38)

SIGNALING (81)

SIGNALING (20)

SIGNALING (22)

SIGNALING (29)

SIGNALING (49)

SIGNALING (39)

SIGNALING (82)

SIGNALING (21)

SIGNALING (24)

SIGNALING (30)

SIGNALING (50)

SIGNALING (41)

SIGNALING (83)

SIGNALING (23)

SIGNALING (36)

SIGNALING (31)

SIGNALING (51)

SIGNALING (47)

SIGNALING (84)

SIGNALING (40)

SIGNALING (78)

SIGNALING (32)

SIGNALING (52)

SIGNALING (48)

SIGNALING (85)

SIGNALING (59)

SIGNALING (92)

SIGNALING (33)

SIGNALING (53)

SIGNALING (56)

SIGNALING (107) SIGNALING (63)

SIGNALING (93)

SIGNALING (34)

SIGNALING (54)

SIGNALING (67)

SIGNALING (110) SIGNALING (66)

SIGNALING (94)

SIGNALING (60)

SIGNALING (55)

SIGNALING (123)

SIGNALING (119) SIGNALING (68)

SIGNALING (95)

SIGNALING (70)

SIGNALING (57)

SIGNALING (128)

SIGNALING (120) SIGNALING (79)

SIGNALING (96)

SIGNALING (71)

SIGNALING (58)

SIGNALING (129)

SIGNALING (142) SIGNALING (86)

SIGNALING (97)

SIGNALING (72)

SIGNALING (61)

SIGNALING (130)

SIGNALING (144) SIGNALING (87)

SIGNALING (98)

SIGNALING (73)

SIGNALING (62)

SIGNALING (131)

SIGNALING (153) SIGNALING (88)

SIGNALING (99)

SIGNALING (74)

SIGNALING (76)

SIGNALING (148)

SIGNALING (154) SIGNALING  (89)

SIGNALING (100) SIGNALING (115) SIGNALING  (77)

SIGNALING (149)

SIGNALING (162) SIGNALING  (90)

SIGNALING (101) SIGNALING (132) SIGNALING (104)

SIGNALING (173) SIGNALING  (91)

SIGNALING (102) SIGNALING (138) SIGNALING (105)

SIGNALING (174) SIGNALING (103) SIGNALING (106) SIGNALING (141) SIGNALING (133)

SIGNALING (175) SIGNALING (108) SIGNALING (112) SIGNALING (146) SIGNALING (134)

SIGNALING (176) SIGNALING (109) SIGNALING (117) SIGNALING (147) SIGNALING (135)

SIGNALING (111) SIGNALING (118) SIGNALING (158) SIGNALING (136)

SIGNALING (113) SIGNALING (124) SIGNALING (159) SIGNALING (137)

SIGNALING (114) SIGNALING (143) SIGNALING (160) SIGNALING (139)

SIGNALING (116) SIGNALING (145) SIGNALING (161) SIGNALING (140)

SIGNALING (121) SIGNALING (150) SIGNALING (165) SIGNALING (152)

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands