manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 732

 

15-106

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Tabular Display of Events and Alarms

Isolating Calls Which Show Internal Symptoms of Problems

To use ERROR and WARN messages isolate calls which show internal symptoms of problems, take the 
following steps:

Step 1

Go to the desired target platform log directory.

$ cd /opt/OptiCall/<platform-instance-name>/bin/logs

Step 2

Use the UNIX 

grep

 command to scan for lines with ERROR or WARN messages.

$  grep "ERROR" *.log 

Step 3

If you find a non-zero CTRAC-ID present in the appropriate column in the trace log, it means that the 
ERROR occurred while a call was being processed. Note the CTRAC-ID.

Step 4

Use the CTRAC-ID to filter out the trace log lines from the BTS 10200 logs.

Billing Fields

The billing record contains a new parameter that contains the CTRAC-ID related to the feature described 
in this document. The CTRAC billing CDR parameter is named CTRACID.

Troubleshooting

The BTS 10200 CTRAC feature is intended as a troubleshooting enabler. No specific troubleshooting 
steps are required other than the use of 

grep

 to filter out the TRACE lines corresponding to a CTRAC-ID.

Tabular Display of Events and Alarms

The BTS 10200 Tabular Display of Events and Alarms feature enables the BTS 10200 to display current 
alarms, alarm history and event history in tabular form. The underlying CPI layer modification will 
easily facilitate other commands to display their data in tabular form.

The BTS 10200 Tabular Display of Events and Alarms feature enables the BTS 10200 to display current 
alarms, alarm history and event history in tabular form. The output of the 

show alarm

 and the 

show 

alarm-log

 commands will provide a tabular output consisting of one alarm per row. Each of the reported 

fields will be columns in the tabular output. This will make the outputs much more conducive to capture 
and printing.

CPI layer changes will facilitate the tabular display of alarms. The CPI layer changes will allow the 
tabular display of other data through derived Request Managers.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands