Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 121

Page: 121 / 874

3-15

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3 Billing Troubleshooting

Billing Events and Alarms

BILLING (36)

For additional information, refer to the

“Billing Link Restored—Billing (36)” section on page 3-30

BILLING (37)

To troubleshoot and correct the cause of the alarm, refer to the

“Billing Link Failure—Billing (37)”

section on page 3-40

DESCRIPTION

Billing Link Restored

SEVERITY

INFO

THRESHOLD

100

THROTTLE

DATAWORDS

Interface Name–STRING [50]

PRIMARY

CAUSE

The cable connection has been restored.

PRIMARY

ACTION

None

DESCRIPTION

Billing Link Failure

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

DATAWORDS

Interface Name–STRING [5]

PRIMARY

CAUSE

The cable connection may have been pulled.

PRIMARY

ACTION

Restore the cable connection.

SECONDARY

CAUSE

ifconfig down

command may have been performed on the interface.

SECONDARY

ACTION

Perform an

ifconfig up

command on the interface.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands